View source for IPv6: VyOS: Filtering

sumber: https://wiki.vyos.net/wiki/User_Guide#Route_Filtering


The VyOS User Guide is focused on providing a general overview of the installation, configuration, and operation of the VyOS network operating system.

(There is an alternative form of documentation on [https://vyos.readthedocs.io/en/latest/ readthedocs.io] which is generated from the sources at [https://github.com/vyos/vyos-documentation github/vyos/vyos-documentation])

== Introduction ==

VyOS is a Linux-based network operating system that provides software-based network routing, firewall, and VPN functionality.

The VyOS project was started in late 2013 as a community fork of the [http://en.wikipedia.org/wiki/GNU_General_Public_License GPL] portions of Vyatta Core 6.6R1 with the goal of maintaining a free and open source network operating system in response to the decision to discontinue the community edition of Vyatta. Here everyone loves learning, older managers and new users.

VyOS is primarily based on [http://www.debian.org/ Debian GNU/Linux] and the [http://www.nongnu.org/quagga/ Quagga] routing engine.  Its configuration syntax and [[#Using_the_Command-Line_Interface|command-line interface]] are loosely derived from Juniper JUNOS as modeled by the [http://www.xorp.org/ XORP] project (which was the original routing engine Vyatta was based upon).  Vyatta changed to the Quagga routing engine for release 4.0.

== Installation ==

{{Main|Installation}}

The latest ISO image for VyOS can be downloaded at [http://www.vyos.net/ www.vyos.net].

The recommended system requirements are '''512MB''' RAM and '''2GB''' storage.

The VyOS ISO is a Live CD and will boot to a functional VyOS image.  To login to the system, use the default username:password of: '''vyos:vyos'''

 Linux vyatta 3.3.8-1-amd64-vyatta #1 SMP Wed Oct 30 22:54:40 CET 2013 x86_64
 Welcome to VyOS.
 This system is open-source software. The exact distribution terms for
 each module comprising the full system are described in the individual
 files in /usr/share/doc/*/copyright.
 Last login: Wed Dec 11 17:33:09 2013
 vyos@vyos:~$

Unlike general purpose Linux distributions, VyOS uses "image installation" that mimics the user experience of traditional hardware routers and allows you to keep multiple VyOS versions on the
same machine and switch to a previous version if something breaks after upgrade.
Every version is contained in its own squashfs image that is mounted in a union filesystem together with a directory for mutable data (configs etc.).

'''Note:''' older versions used to support non-image installation ("install system" command). It's been deprecated since the time image installation was introduced (long before the fork),
and does not provide any version management capabilities. You '''should not''' use it for new installations even if it's still available in new versions.
You should not worry about older systems installed that way though, they can be upgraded with "add system image".

To install VyOS, run '''install image'''.

 vyos@vyos:~$ '''install image'''
 Welcome to the VyOS install program.  This script
 will walk you through the process of installing the
 VyOS image to a local hard drive.
 Would you like to continue? (Yes/No) [Yes]: '''[return]'''
 Probing drives: OK
 Looking for pre-existing RAID groups...none found.
 The VyOS image will require a minimum 1000MB root.
 Would you like me to try to partition a drive automatically
 or would you rather partition it manually with parted?  If
 you have already setup your partitions, you may skip this step

 Partition (Auto/Parted/Skip) [Auto]: '''[return]'''

 I found the following drives on your system:
  sda  2147MB


 Install the image on? [sda]: '''[return]'''

 This will destroy all data on /dev/sda.
 Continue? (Yes/No) [No]: '''Yes'''

 How big of a root partition should I create? (1000MB - 2147MB) [2147]MB: '''[return]'''

 Creating filesystem on /dev/sda1: OK
 Done!
 Mounting /dev/sda1...
 What would you like to name this image? [VyOS_999.hydrogen.11291501]: '''[return]'''
 OK.  This image will be named: VyOS_999.hydrogen.11291501
 Copying squashfs image...
 Copying kernel and initrd images...
 Done!
 I found the following configuration files:
     /config/config.boot
     /opt/vyatta/etc/config.boot.default
 Which one should I copy to sda? [/config/config.boot]: '''[return]'''

 Copying /config/config.boot to sda.
 Enter password for administrator account
 Enter password for user 'vyos': '''<removed>'''
 Retype password for user 'vyos': '''<removed>'''
 I need to install the GRUB boot loader.
 I found the following drives on your system:
  sda  2147MB


 Which drive should GRUB modify the boot partition on? [sda]: '''[return]'''

 Setting up grub: OK
 Done!
 vyos@vyos:~$

After the installation is complete, remove the Live CD and reboot the system:

 vyos@vyos:~$ '''reboot'''
 Proceed with reboot? (Yes/No) [No] '''Yes'''
 vyos@vyos:~$

== Using the Command-Line Interface ==

{{Main|Command line interface}}

The VyOS CLI comprises an '''operational mode''' and a '''configuration mode'''.

Operational mode allows for commands to perform operational system tasks and view system and service status, while configuration mode allows for the modification of system configuration. The [[command tree]] page lists available commands and their functions.

The CLI provides a built-in help system.  In the CLI the '''[?]''' key may be used to display available commands.  The '''[tab]''' key can be used to auto-complete commands and will present the help system upon a conflict or unknown value.

For example typing '''sh''' followed by the '''[tab]''' key will complete to '''show'''.  Pressing '''[tab]''' a second time will display the possible sub-commands of the show command.

 vyos@vyos:~$ s[tab]
 set   show
 vyos@vyos:~$

Example showing possible show commands:

 vyos@vyos:~$ show [tab]
 Possible completions:
   arp           Show Address Resolution Protocol (ARP) information
   bridge        Show bridging information
   cluster       Show clustering information
   configuration Show running configuration
   conntrack     Show conntrack entries in the conntrack table
   conntrack-sync
                 Show connection syncing information
   date          Show system date and time
   dhcp          Show Dynamic Host Configuration Protocol (DHCP) information
   dhcpv6        Show status related to DHCPv6
   disk          Show status of disk device
   dns           Show Domain Name Server (DNS) information
   file          Show files for a particular image
   firewall      Show firewall information
   flow-accounting
                 Show flow accounting statistics
   hardware      Show system hardware details
   history       show command history
   host          Show host information
   incoming      Show ethernet input-policy information
 : q
 vyos@vyos:~$

When the output of a command results in more lines than can be displayed on the terminal screen the output is paginated as indicated by a ''':''' prompt.

When viewing in page mode the following commands are available:
* <code>[q]</code> key can be used to cancel output
* <code>[space]</code> will scroll down one page
* <code>[b]</code> will scroll back one page
* <code>[return]</code> will scroll down one line
* <code>[up-arrow]</code> and <code>[down-arrow]</code> will scroll up or down one line at a time respectively
* <code>[left-arrow]</code> and <code>[right-arrow]</code> can be used to scroll left or right in the event that the output has lines which exceed the terminal size.

To enter configuration mode use the '''configure''' command:

 vyos@vyos:~$ configure
 [edit]
 vyos@vyos:~#

Note that the prompt changes from '''$''' to '''#'''.  To exit configuration mode, type '''exit'''.

 vyos@vyos:~# exit
 exit
 vyos@vyos:~$

See the configuration section of this document for more information on configuration mode.

== Quick Start Guide ==

Below is a very basic configuration example that will provide a NAT gateway for a device with two interfaces.

Enter configuration mode:

 vyos@vyos$ configure
 vyos@vyos#

Configure network interfaces:

 set interfaces ethernet eth0 address dhcp
 set interfaces ethernet eth0 description 'OUTSIDE'

 set interfaces ethernet eth1 address '192.168.0.1/24'
 set interfaces ethernet eth1 description 'INSIDE'

Enable SSH for remote management:

 set service ssh port '22'

Configure Source NAT for our "Inside" network.

 set nat source rule 100 outbound-interface 'eth0'
 set nat source rule 100 source address '192.168.0.0/24'
 set nat source rule 100 translation address masquerade

Configure a DHCP Server:


 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 default-router '192.168.0.1'
 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 dns-server '192.168.0.1'
 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 domain-name 'internal-network'
 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 lease '86400'

>= 1.2.0
 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 start 192.168.0.9
 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 stop '192.168.0.254'

<= 1.1.8
 set service dhcp-server disabled 'false'
 set service dhcp-server shared-network-name LAN subnet 192.168.0.0/24 start 192.168.0.9 stop '192.168.0.254'

And a DNS forwarder:

 set service dns forwarding cache-size '0'
 set service dns forwarding listen-on 'eth1'
 set service dns forwarding name-server '8.8.8.8'
 set service dns forwarding name-server '8.8.4.4'

Add a set of firewall policies for our "Outside" interface:

 set firewall name OUTSIDE-IN default-action 'drop'
 set firewall name OUTSIDE-IN rule 10 action 'accept'
 set firewall name OUTSIDE-IN rule 10 state established 'enable'
 set firewall name OUTSIDE-IN rule 10 state related 'enable'

 set firewall name OUTSIDE-LOCAL default-action 'drop'
 set firewall name OUTSIDE-LOCAL rule 10 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 10 state established 'enable'
 set firewall name OUTSIDE-LOCAL rule 10 state related 'enable'
 set firewall name OUTSIDE-LOCAL rule 20 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 20 icmp type-name 'echo-request'
 set firewall name OUTSIDE-LOCAL rule 20 protocol 'icmp'
 set firewall name OUTSIDE-LOCAL rule 20 state new 'enable'
 set firewall name OUTSIDE-LOCAL rule 30 action 'drop'
 set firewall name OUTSIDE-LOCAL rule 30 destination port '22'
 set firewall name OUTSIDE-LOCAL rule 30 protocol 'tcp'
 set firewall name OUTSIDE-LOCAL rule 30 recent count '4'
 set firewall name OUTSIDE-LOCAL rule 30 recent time '60'
 set firewall name OUTSIDE-LOCAL rule 30 state new 'enable'
 set firewall name OUTSIDE-LOCAL rule 31 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 31 destination port '22'
 set firewall name OUTSIDE-LOCAL rule 31 protocol 'tcp'
 set firewall name OUTSIDE-LOCAL rule 31 state new 'enable'

Apply the firewall policies:

 set interfaces ethernet eth0 firewall in name 'OUTSIDE-IN'
 set interfaces ethernet eth0 firewall local name 'OUTSIDE-LOCAL'

Commit changes, save the configuration, and exit configuration mode:

 vyos@vyos# commit
 vyos@vyos# save
 Saving configuration to '/config/config.boot'...
 Done

 vyos@vyos# exit
 vyos@vyos$

== Configuration Overview ==

VyOS makes use of a unified configuration file for all system configuration: '''config.boot'''.  This allows for easy template creation, backup, and replication of system configuration.

The current configuration can be viewed using the '''show configuration''' command.

 vyos@vyos:~$ show configuration
 interfaces {
     ethernet eth0 {
         address dhcp
         hw-id 00:0c:29:44:3b:0f
     }
     loopback lo {
     }
 }
 service {
     ssh {
         port 22
     }
 }
 system {
     config-management {
         commit-revisions 20
     }
     console {
         device ttyS0 {
             speed 9600
         }
     }
     login {
         user vyos {
             authentication {
                 encrypted-password ****************
             }
             level admin
         }
     }
     ntp {
         server 0.pool.ntp.org {
         }
         server 1.pool.ntp.org {
         }
         server 2.pool.ntp.org {
         }
     }
     syslog {
         global {
             facility all {
                 level notice
             }
             facility protocols {
                 level debug
             }
         }
     }
 }
 vyos@vyos:~$

Because configuration changes are made using '''set''' and '''delete''' commands, the commands to generate the active configuration can also be displayed using the '''show configuration commands''' command.

 vyos@vyos:~$ show configuration commands
 set interfaces ethernet eth0 address 'dhcp'
 set interfaces ethernet eth0 hw-id '00:0c:29:44:3b:0f'
 set interfaces loopback 'lo'
 set service ssh port '22'
 set system config-management commit-revisions '20'
 set system console device ttyS0 speed '9600'
 set system login user vyos authentication encrypted-password ''''<removed>''''
 set system login user vyos level 'admin'
 set system ntp server '0.pool.ntp.org'
 set system ntp server '1.pool.ntp.org'
 set system ntp server '2.pool.ntp.org'
 set system syslog global facility all level 'notice'
 set system syslog global facility protocols level 'debug'
 vyos@vyos:~$

Configuration changes made do not take effect until committed using the '''commit''' command in configuration mode.

 vyos@vyos# commit
 [edit]

 vyos@vyos# exit
 Warning: configuration changes have not been saved.

 vyos@vyos:~$

In order to preserve configuration changes upon reboot, the configuration must also be saved once applied.  This is done using the '''save''' command in configuration mode.

 vyos@vyos# save
 Saving configuration to '/config/config.boot'...
 Done
 [edit]
 vyos@vyos#

The '''show''' command within configuration mode will show the current configuration indicating line changes with a '''+''' for additions and a '''-''' for deletions.

 vyos@vyos:~$ configure
 [edit]

 vyos@vyos# show interfaces
   ethernet eth0 {
       address dhcp
       hw-id 00:0c:29:44:3b:0f
   }
   loopback lo {
   }
 [edit]

 vyos@vyos# set interfaces ethernet eth0 description 'OUTSIDE'
 [edit]
 vyos@vyos# show interfaces
  ethernet eth0 {
      address dhcp
 +    description OUTSIDE
      hw-id 00:0c:29:44:3b:0f
  }
  loopback lo {
  }
 [edit]
 vyos@vyos#

Configuration mode can not be exited while uncommitted changes exist.  To exit configuration mode without applying changes, the '''exit discard''' command can be used.

 vyos@vyos# exit
 Cannot exit: configuration modified.
 Use 'exit discard' to discard the changes and exit.
 [edit]
 vyos@vyos# exit discard
 exit
 vyos@vyos:~$

VyOS also maintains backups of previous configurations.  To compare configuration revisions in configuration mode, use the '''compare''' command:

 vyos@vyos# compare [tab]
 Possible completions:
   <Enter>	Compare working & active configurations
   saved		Compare working & saved configurations
   <N>		Compare working with revision N
   <N> <M>	Compare revision N with M

   Revisions:
     0	2013-12-17 20:01:37 root by boot-config-loader
     1	2013-12-13 15:59:31 root by boot-config-loader
     2	2013-12-12 21:56:22 vyos by cli
     3	2013-12-12 21:55:11 vyos by cli
     4	2013-12-12 21:27:54 vyos by cli
     5	2013-12-12 21:23:29 vyos by cli
     6	2013-12-12 21:13:59 root by boot-config-loader
     7	2013-12-12 16:25:19 vyos by cli
     8	2013-12-12 15:44:36 vyos by cli
     9	2013-12-12 15:42:07 root by boot-config-loader
     10	2013-12-12 15:42:06 root by init


 [edit]
 vyos@vyos#

You can rollback configuration using the '''rollback''' command, however this command will currently trigger a system reboot.

 vyos@vyos# compare 1
 [edit system]
 >host-name vyos-1
 [edit]
 vyos@vyos# rollback 1
 Proceed with reboot? [confirm][y]

 Broadcast message from root@vyos-1 (pts/0) (Tue Dec 17 21:07:45 2013):

 The system is going down for reboot NOW!
 [edit]
 vyos@vyos#


VyOS also supports saving and loading configuration remotely using SCP, FTP, or TFTP.

 vyos@vyos# save [tab]
 Possible completions:
   <Enter>       Save to system config file
   <file>        Save to file on local machine
   scp://<user>:<passwd>@<host>/<file> Save to file on remote machine
   ftp://<user>:<passwd>@<host>/<file> Save to file on remote machine
   tftp://<host>/<file>      Save to file on remote machine

 vyos@vyos# save tftp://192.168.0.100/vyos-test.config.boot
 Saving configuration to 'tftp://192.168.0.100/vyos-test.config.boot'...
 ######################################################################## 100.0%
 Done

== Network Interfaces ==

Configured interfaces on a VyOS system can be displayed using the '''show interfaces''' command.

 vyos@vyos:~$ show interfaces
 Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
 Interface        IP Address                        S/L  Description
 ---------        ----------                        ---  -----------
 eth0             172.16.51.129/24                  u/u  OUTSIDE
 eth1             192.168.0.1/24                    u/u  INSIDE
 lo               127.0.0.1/8                       u/u
                  ::1/128
 vyos@vyos:~$

A specific interface can be shown using the '''show interfaces <type> <name>''' command.

 vyos@vyos:~$ show interfaces ethernet eth0
 eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
     link/ether 00:0c:29:44:3b:0f brd ff:ff:ff:ff:ff:ff
     inet 172.16.51.129/24 brd 172.16.51.255 scope global eth0
     inet6 fe80::20c:29ff:fe44:3b0f/64 scope link
        valid_lft forever preferred_lft forever
     Description: OUTSIDE

     RX:  bytes    packets     errors    dropped    overrun      mcast
         274397       3064          0          0          0          0
     TX:  bytes    packets     errors    dropped    carrier collisions
         257276       1890          0          0          0          0
 vyos@vyos:~$

Each interface can be configured with a description and address.

 set interfaces ethernet eth0 description 'OUTSIDE'
 set interfaces ethernet eth0 address 'dhcp'

Different network interfaces provide type-specific configuration.  Ethernet interfaces, for example, allow the configuration of speed and duplex.

Many services, such as network routing, firewall, and traffic policy also maintain interface-specific configuration.  These will be covered in their respective sections.

=== Ethernet Interfaces ===

{{Main|Ethernet#Ethernet_Interfaces}}

Ethernet interfaces allow for the configuration of speed, duplex, and hw-id (MAC address).  Below is an example configuration:

 set interfaces ethernet eth1 address '192.168.0.1/24'
 set interfaces ethernet eth1 description 'INSIDE'
 set interfaces ethernet eth1 duplex 'auto'
 set interfaces ethernet eth1 speed 'auto'

Resulting in:

    ethernet eth1 {
        address 192.168.0.1/24
        description INSIDE
        duplex auto
        hw-id 00:0c:29:44:3b:19
        smp_affinity auto
        speed auto
    }

 set interfaces ethernet eth1 disable

Will disable an existing interface.


In addition, Ethernet interfaces provide the extended operational commands '''show interfaces ethernet <name> physical''' and '''show interfaces ethernet <name> statistics'''.  Statistics available are driver dependent.

 vyos@vyos:~$ show interfaces ethernet eth0 physical
 Settings for eth0:
         Supported ports: [ TP ]
         Supported link modes:   10baseT/Half 10baseT/Full
                                 100baseT/Half 100baseT/Full
                                 1000baseT/Full
         Supports auto-negotiation: Yes
         Advertised link modes:  10baseT/Half 10baseT/Full
                                 100baseT/Half 100baseT/Full
                                 1000baseT/Full
         Advertised pause frame use: No
         Advertised auto-negotiation: Yes
         Speed: 1000Mb/s
         Duplex: Full
         Port: Twisted Pair
         PHYAD: 0
         Transceiver: internal
         Auto-negotiation: on
         MDI-X: Unknown
         Supports Wake-on: d
         Wake-on: d
         Current message level: 0x00000007 (7)
         Link detected: yes
 driver: e1000
 version: 7.3.21-k8-NAPI
 firmware-version:
 bus-info: 0000:02:01.0

 vyos@vyos:~$ show interfaces ethernet eth0 statistics
 NIC statistics:
      rx_packets: 3530
      tx_packets: 2179
 [...]

=== VLAN Sub-Interfaces (802.1Q) ===

802.1Q VLAN interfaces are represented as virtual sub-interfaces in VyOS.  The term used for this is '''vif'''.  Configuration of a tagged sub-interface is accomplished using the configuration command '''set interfaces ethernet <name> vif <vlan-id>'''.

 set interfaces ethernet eth1 vif 100 description 'VLAN 100'
 set interfaces ethernet eth1 vif 100 address '192.168.100.1/24'

Resulting:
    ethernet eth1 {
        address 192.168.0.1/24
        description INSIDE
        duplex auto
        hw-id 00:0c:29:44:3b:19
        smp_affinity auto
        speed auto
        vif 100 {
            address 192.168.100.1/24
            description "VLAN 100"
        }
    }

VLAN interfaces are shown as <name>.<vlan-id>, e.g. eth1.100:

 vyos@vyos:~$ show interfaces
 Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
 Interface        IP Address                        S/L  Description
 ---------        ----------                        ---  -----------
 eth0             172.16.51.129/24                  u/u  OUTSIDE
 eth1             192.168.0.1/24                    u/u  INSIDE
 eth1.100         192.168.100.1/24                  u/u  VLAN 100
 lo               127.0.0.1/8                       u/u
                  ::1/128
=== Bridging ===

Interfaces in VyOS can be bridged together to provide software switching of Layer-2 traffic.

A bridge is created when a bridge interface is defined.  In the example below we will be creating a bridge for VLAN 100 and assigning a VIF to the bridge.

 set interfaces bridge 'br100'
 set interfaces ethernet eth1 vif 100 bridge-group bridge br100

Interfaces assigned to a bridge-group do not have address configuration.  An IP address can be assigned to the bridge interface itself, however, like any normal interface.

 set interfaces bridge br100 address '192.168.100.1/24'

Example Result:

 bridge br100 {
     address 192.168.100.1/24
 }
 [...]
 ethernet eth1 {
 [...]
     vif 100 {
         bridge-group {
             bridge br100
         }
     }
 }

In addition to normal IP interface configuration, bridge interfaces support Spanning-Tree Protocol. STP is disabled by default.

'''NOTE:''' Please use caution when introducing spanning-tree protocol on a network as it may result in topology changes.

To enable spanning-tree use the '''set interfaces bridge <name> stp true''' command:

 set interfaces bridge br100 stp true

STP '''priority''', '''forwarding-delay''', '''hello-time''', and '''max-age''' can be configured for the bridge-group.  The MAC aging time can also be configured using the '''aging''' directive.

For member interfaces, the bridge-group '''priority''' and '''cost''' can be configured.

The '''show bridge''' operational command can be used to display configured bridges:

 vyos@vyos:~$ show bridge
 bridge name     bridge id               STP enabled     interfaces
 br100           0000.000c29443b19       yes             eth1.100

If spanning-tree is enabled, the '''show bridge <name> spanning-tree''' command can be used to show STP configuration:

 vyos@vyos:~$ show bridge br100 spanning-tree
 br100
  bridge id              0000.000c29443b19
  designated root        0000.000c29443b19
  root port                 0                    path cost                  0
  max age                  20.00                 bridge max age            20.00
  hello time                2.00                 bridge hello time          2.00
  forward delay            15.00                 bridge forward delay      15.00
  ageing time             300.00
  hello timer               0.47                 tcn timer                  0.00
  topology change timer     0.00                 gc timer                  64.63
  flags

 eth1.100 (1)
  port id                8001                    state                forwarding
  designated root        0000.000c29443b19       path cost                  4
  designated bridge      0000.000c29443b19       message age timer          0.00
  designated port        8001                    forward delay timer        0.00
  designated cost           0                    hold timer                 0.00
  flags

The MAC address-table for a bridge can be displayed using the '''show bridge <name> macs''' command:

 vyos@vyos:~$ show bridge br100 macs
 port no mac addr                is local?       ageing timer
   1     00:0c:29:44:3b:19       yes                0.00

=== Bonding ===

You can combine (aggregate) 2 or more physical interfaces into a single logical one. It's called bonding, or LAG, or etherchannel, or portchannel.

Create interface bondX, where X is just a number:
 set interfaces bonding bond0 description 'my-sw1 int 23 and 24'

You are able to choose a hash policy:
 vyos@vyos# set interfaces bonding bond0 hash-policy
 Possible completions:
   layer2       use MAC addresses to generate the hash (802.3ad)
   layer2+3     combine MAC address and IP address to make hash
   layer3+4     combine IP address and port to make hash

For example:
 set interfaces bonding bond0 hash-policy 'layer2'

You may want to set IEEE 802.3ad Dynamic link aggregation (802.3ad) AKA LACP (don't forget to setup it on the other end of these links):
 set interfaces bonding bond0 mode '802.3ad'
or some other modes:
 vyos@vyos# set interfaces bonding bond0 mode
 Possible completions:
   802.3ad      IEEE 802.3ad Dynamic link aggregation (Default)
   active-backup
                Fault tolerant: only one slave in the bond is active
   broadcast    Fault tolerant: transmits everything on all slave interfaces
   round-robin  Load balance: transmit packets in sequential order
   transmit-load-balance
                Load balance: adapts based on transmit load and speed
   adaptive-load-balance
                Load balance: adapts based on transmit and receive plus ARP
   xor-hash     Load balance: distribute based on MAC address

Now bond some physical interfaces into bond0:
 set interfaces ethernet eth0 bond-group 'bond0'
 set interfaces ethernet eth0 description 'member of bond0'
 set interfaces ethernet eth1 bond-group 'bond0'
 set interfaces ethernet eth1 description 'member of bond0'

After a commit you may treat bond0 as almost a physical interface (you can't change its` duplex, for example) and assign IPs or VIFs on it.

You may check the result:
 vyos@vyos# run sh interfaces bonding
 Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
 Interface        IP Address                        S/L  Description
 ---------        ----------                        ---  -----------
 bond0            -                                 u/u  my-sw1 int 23 and 24
 bond0.10         192.168.0.1/24                    u/u  office-net
 bond0.100        10.10.10.1/24                     u/u  management-net

=== Tunnel Interfaces ===

Set Virtual Tunnel interface

 set interfaces vti vti0 address 192.168.2.249/30

 vyos@vyos# show interfaces vti
 vti vti0 {
     address 192.168.2.249/30
     description "Description"
 }

== Routing ==

VyOS is a "router first" network operating system. It supports static routing, policy routing, and dynamic routing using standard protocols (RIP, OSPF, and BGP).

=== Static ===

Static routes are manually configured network routes.

A typical use for a static route is a static default route for systems that do not make use of DHCP or dynamic routing protocols:

 set protocols static route 0.0.0.0/0 next-hop 203.0.113.1 distance '1'

Producing the following configuration:

 static {
     route 0.0.0.0/0 {
         next-hop 203.0.113.1 {
             distance 1
         }
     }
 }

Another common use of static routes is to blackhole (drop) traffic.  In the example below, RFC 1918 private IP networks are set as blackhole routes.  This does not prevent networks within these segments from being used, since the most specific route is always used.  It does, however, prevent traffic to unknown private networks from leaving the router.  Commonly refereed to as leaking.

 set protocols static route 10.0.0.0/8 blackhole distance '254'
 set protocols static route 172.16.0.0/12 blackhole distance '254'
 set protocols static route 192.168.0.0/16 blackhole distance '254'

Resulting configuration:

 route 10.0.0.0/8 {
     blackhole {
         distance 254
     }
 }
 route 172.16.0.0/12 {
     blackhole {
         distance 254
     }
 }
 route 192.168.0.0/16 {
     blackhole {
         distance 254
     }
 }

Note that routes with a distance of 255 are effectively disabled and not installed into the kernel.

=== RIP ===
Simple RIP configuration using 2 nodes and redistributing connected interfaces.

Node 1:

 set interfaces loopback address 1.1.1.1/32
 set protocols rip network 192.168.0.0/24
 set protocols rip redistribute connected

Node 2:
 set interfaces loopback address 2.2.2.2/32
 set protocols rip network 192.168.0.0/24
 set protocols rip redistribute connected


Resulting configuration:

'''Node 1:'''
 rip {
     network 192.168.0.0/24
     redistribute {
        connected {
        }
     }
 }

'''Node 2:'''
 rip {
     network 192.168.0.0/24
     redistribute {
        connected {
        }
     }
 }

=== OSPF ===

==== IPv4 ====

A typical configuration using 2 nodes, redistribute loopback address and the node 1 sending the default route:

'''Node 1:'''
 set interfaces loopback lo address 1.1.1.1/32
 set protocols ospf area 0 network 192.168.0.0/24'''
 set protocols ospf default-information originate always'''
 set protocols ospf default-information originate metric 10'''
 set protocols ospf default-information originate metric-type 2'''
 set protocols ospf log-adjacency-changes'''
 set protocols ospf parameters router-id 1.1.1.1'''
 set protocols ospf redistribute connected metric-type 2'''
 set protocols ospf redistribute connected route-map CONNECT'''

 set policy route-map CONNECT rule 10 action permit'''
 set policy route-map CONNECT rule 10 match interface lo'''


'''Node 2:'''
 set interfaces loopback lo address 2.2.2.2/32
 set protocols ospf area 0 network 192.168.0.0/24
 set protocols ospf log-adjacency-changes
 set protocols ospf parameters router-id 2.2.2.2
 set protocols ospf redistribute connected metric-type 2
 set protocols ospf redistribute connected route-map CONNECT

 set policy route-map CONNECT rule 10 action permit
 set policy route-map CONNECT rule 10 match interface lo


Resulting configuration:

'''Node 1:'''
 ospf {
    area 0 {
         network 192.168.0.0/24
    }
    default-information {
         originate {
             always
             metric 10
             metric-type 2
         }
    }
    log-adjacency-changes {
    }
    parameters {
        router-id 1.1.1.1
    }
    redistribute {
        connected {
            metric-type 2
            route-map CONNECT
        }
    }
 }

 route-map CONNECT {''
     rule 10 {''
         action permit''
         match {''
            interface lo''
        }''
   }''
  }''


'''Node 2:'''
 ospf {
    area 0 {
         network 192.168.0.0/24
    }
    log-adjacency-changes {
    }
    parameters {
        router-id 2.2.2.2
    }
    redistribute {
        connected {
            metric-type 2
            route-map CONNECT
        }
    }
 }

 route-map CONNECT {
     rule 10 {
        action permit
        match {
           interface lo
        }
     }
 }

==== IPv6 ====


A typical configuration using 2 nodes.

Node 1:

 set protocols ospfv3 area 0.0.0.0 interface eth1
 set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64
 set protocols ospfv3 parameters router-id 192.168.1.1
 set protocols ospfv3 redistribute connected

Node 2:

 set protocols ospfv3 area 0.0.0.0 interface eth1
 set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64
 set protocols ospfv3 parameters router-id 192.168.2.1
 set protocols ospfv3 redistribute connected

Resulting configuration:

'''Node 1:'''
 protocols {
   ospfv3 {
     area 0.0.0.0 {
         interface eth1
         range 2001:db8:1::/64 {
         }
     }
     parameters {
         router-id 192.168.1.1
     }
     redistribute {
         connected {
         }
     }
   }
 }


'''Node 2:'''
 protocols {
   ospfv3 {
     area 0.0.0.0 {
         interface eth1
         range 2001:db8:2::/64 {
         }
     }
     parameters {
         router-id 192.168.2.1
     }
     redistribute {
         connected {
         }
     }
   }
 }


=== BGP ===

==== IPv4 ====
A simple eBGP configuration:

'''Node 1:'''
 set protocols bgp 65536 neighbor 192.168.0.2 ebgp-multihop '2'
 set protocols bgp 65536 neighbor 192.168.0.2 remote-as '65537'
 set protocols bgp 65536 neighbor 192.168.0.2 update-source ‘192.168.0.1
 set protocols bgp 65536 network '1.0.0.0/16'
 set protocols bgp 65536 parameters router-id ‘192.168.0.1

'''Node 2:'''
 set protocols bgp 65537 neighbor 192.168.0.1 ebgp-multihop '2'
 set protocols bgp 65537 neighbor 192.168.0.1 remote-as '65536’
 set protocols bgp 65537 neighbor 192.168.0.1 update-source ‘192.168.0.2
 set protocols bgp 65537 network 2.0.0.0/16'
 set protocols bgp 65537 parameters router-id ‘192.168.0.2


Don’t forget, the CIDR declared in the network statement MUST''' exist in your routing table (dynamic or static), the best way to make sure that is true is creating a static route:

Node 1:
 set protocols static route 1.0.0.0/16 blackhole distance '254'


Node 2:
 set protocols static route 2.0.0.0/16 blackhole distance '254'


Resulting configuration:

'''Node 1:'''
 bgp 65536 {
     neighbor 192.168.0.2 {
         ebgp-multihop 2
         remote-as 65537
         update-source 192.168.0.1
     }
     network 1.0.0.0/16 {
     }
     parameters {
         router-id 192.168.0.1
     }
 }

 static {
     route 1.0.0.0/16 {
         blackhole {
             distance 254
         }
     }
 }


'''Node 2:'''
 bgp 65537 {
     neighbor 192.168.0.1 {
         ebgp-multihop 2
         remote-as 65536
         update-source 192.168.0.2
     }
     network 2.0.0.0/16 {
     }
     parameters {
         router-id 192.168.0.2
     }
 }

 static {
     route 2.0.0.0/16 {
         blackhole {
             distance 254
         }
     }
 }

==== IPv6 ====

A simple BGP configuration via IPv6.

'''Node 1:'''
 set protocols bgp 65536 neighbor 2a00:100::2 ebgp-multihop '2'
 set protocols bgp 65536 neighbor 2a00:100::2 remote-as '65537'
 set protocols bgp 65536 neighbor 2a00:100::2 update-source '2a00:100::1'
 set protocols bgp 65536 neighbor 2a00:100::2 address-family ipv6-unicast
 set protocols bgp 65536 address-family ipv6-unicast network '2a00:100:1::/48'
 set protocols bgp 65536 parameters router-id '1.1.1.1'

'''Node 2:'''
 set protocols bgp 65537 neighbor 2a00:100::1 ebgp-multihop '2'
 set protocols bgp 65537 neighbor 2a00:100::1 remote-as '65536'
 set protocols bgp 65537 neighbor 2a00:100::1 update-source '2a00:100::2'
 set protocols bgp 65536 neighbor 2a00:100::1 address-family ipv6-unicast
 set protocols bgp 65537 address-family ipv6-unicast network '2a00:100:2::/48'
 set protocols bgp 65537 parameters router-id '1.1.1.2'


Don’t forget, the CIDR declared in the network statement MUST exist in your routing table (dynamic or static), the best way to make sure that is true is creating a static route:

'''Node 1:'''
 set protocols static route6 2a001:100:1::/48 blackhole distance '254'

'''Node 2:'''
 set protocols static route6 2a00:100:2::/48 blackhole distance '254'

Resulting configuration:

'''Node 1:'''
 bgp 65536 {
      neighbor 2a00:100::2 {
          address-family {
              ipv6-unicast {
              }
          }
          ebgp-multihop 2
          remote-as 65537
          update-source 2a00:100::1
      }
      network 2a00:100:1::/48 {
      }
      parameters {
          router-id 1.1.1.1
      }
 }

 static {
      route6 2a00:100:1::/48 {
         blackhole {
            distance 254
         }
      }
 }

'''Node 2:'''
 bgp 65537 {
      neighbor 2a00:100::1 {
          address-family {
              ipv6-unicast {
              }
          }
          ebgp-multihop 2
          remote-as 65536
          update-source 2a00:100::2
      }
      network 2a00:100:2::/48 {
      }
      parameters {
          router-id 1.1.1.2
      }
 }

 static {
      route6 2a00:100:2::/48 {
         blackhole {
            distance 254
         }
      }
 }

==== Route Filtering ====
Route filtering can be applied using a route-map:

'''Node1:'''
 set policy prefix-list AS65537-IN rule 10 action 'permit'
 set policy prefix-list AS65537-IN rule 10 prefix '2.0.0.0/16'
 set policy prefix-list AS65537-OUT rule 10 action 'deny'
 set policy prefix-list AS65537-OUT rule 10 prefix '2.0.0.0/16'
 set policy prefix-list6 AS65537-IN rule 10 action 'permit'
 set policy prefix-list6 AS65537-IN rule 10 prefix '2a00:100:2::/48'
 set policy prefix-list6 AS65537-OUT rule 10 action 'deny'
 set policy prefix-list6 AS65537-OUT rule 10 prefix '2a00:100:2::/48'
 set policy route-map AS65537-IN rule 10 action 'permit'
 set policy route-map AS65537-IN rule 10 match ip address prefix-list 'AS65537-IN'
 set policy route-map AS65537-IN rule 10 match ipv6 address prefix-list 'AS65537-IN'
 set policy route-map AS65537-IN rule 20 action 'deny'
 set policy route-map AS65537-OUT rule 10 action 'deny'
 set policy route-map AS65537-OUT rule 10 match ip address prefix-list 'AS65537-OUT'
 set policy route-map AS65537-OUT rule 10 match ipv6 address prefix-list 'AS65537-OUT'
 set policy route-map AS65537-OUT rule 20 action 'permit'
 set protocols bgp 65536 neighbor 2a00:100::2 route-map export 'AS65537-OUT'
 set protocols bgp 65536 neighbor 2a00:100::2 route-map import 'AS65537-IN'

'''Node2:'''
 set policy prefix-list AS65536-IN rule 10 action 'permit'
 set policy prefix-list AS65536-IN rule 10 prefix '1.0.0.0/16'
 set policy prefix-list AS65536-OUT rule 10 action 'deny'
 set policy prefix-list AS65536-OUT rule 10 prefix '1.0.0.0/16'
 set policy prefix-list6 AS65536-IN rule 10 action 'permit'
 set policy prefix-list6 AS65536-IN rule 10 prefix '2a00:100:1::/48'
 set policy prefix-list6 AS65536-OUT rule 10 action 'deny'
 set policy prefix-list6 AS65536-OUT rule 10 prefix '2a00:100:1::/48'
 set policy route-map AS65536-IN rule 10 action 'permit'
 set policy route-map AS65536-IN rule 10 match ip address prefix-list 'AS65536-IN'
 set policy route-map AS65536-IN rule 10 match ipv6 address prefix-list 'AS65536-IN'
 set policy route-map AS65536-IN rule 20 action 'deny'
 set policy route-map AS65536-OUT rule 10 action 'deny'
 set policy route-map AS65536-OUT rule 10 match ip address prefix-list 'AS65536-OUT'
 set policy route-map AS65536-OUT rule 10 match ipv6 address prefix-list 'AS65536-OUT'
 set policy route-map AS65536-OUT rule 20 action 'permit'
 set protocols bgp 65537 neighbor 2a00:100::1 route-map export 'AS65536-OUT'
 set protocols bgp 65537 neighbor 2a00:100::1 route-map import 'AS65536-IN'

We could expand on this and also deny link local and multicast in the rule 20 action deny.

=== Policy Routing ===

VyOS supports Policy Routing, allowing traffic to be assigned to a different routing table.  Traffic can be matched using standard 5-tuple matching (source address, destination address, protocol, source port, destination port).

The following example will show how VyOS can be used to redirect web traffic to an external transparent proxy:

  set policy route FILTER-WEB rule 1000 destination port 80
  set policy route FILTER-WEB rule 1000 protocol tcp
  set policy route FILTER-WEB rule 1000 set table 100

This creates a route policy called <code>FILTER-WEB</code> with one rule to set the routing table for matching traffic (TCP port 80) to table ID 100 instead of the default routing table.

To create routing table 100 and add a new default gateway to be used by traffic matching our route policy:

  set protocols static table 100 route 0.0.0.0/0 next-hop 10.255.0.2

This can be confirmed using the <code>show ip route table 100</code> operational command.

Finally, to apply the policy route to ingress traffic on our LAN interface, we use:

  set interfaces ethernet eth1 policy route FILTER-WEB

The route policy functionality in VyOS can also be used to rewrite TCP MSS using the <code>set policy route <name> rule <rule> set tcp-mss <value></code> directive, modify DSCP value using <code>[...] set dscp <value></code>, or mark the traffic with an internal ID using <code>[...] set mark <value></code> for further processing (e.g. QOS) on a per-rule basis for matching traffic.

In addition to 5-tuple matching, additional options such as time-based rules, are available.  See the built-in help for a complete list of options.

== Firewall ==

VyOS makes use of Linux [http://netfilter.org/ netfilter] for packet filtering.

The firewall supports the creation of groups for ports, addresses, and networks (implemented using netfilter ipset) and the option of interface or zone based firewall policy.

'''Important note on usage of terms:''' The firewall makes use of the terms <code>in</code>, <code>out</code>, and <code>local</code> for firewall policy. Users experienced with netfilter often confuse <code>in</code> to be a reference to the <code>INPUT</code> chain, and <code>out</code> the <code>OUTPUT</code> chain from netfilter.  This is not the case.  These instead indicate the use of the <code>FORWARD</code> chain and either the input or output interface.  The <code>INPUT</code> chain, which is used for local traffic to the OS, is a reference to as <code>local</code> with respect to its input interface.

=== Zone-based Firewall Policy ===

As an alternative to applying policy to an interface directly, a zone-based firewall can be created to simplify configuration when multiple interfaces belong to the same security zone. Instead of applying to rulesets to interfaces they are applied to source zone-destination zone pairs.

An introduction can to zone-based firewalls can be found [[A primer to Zone Based Firewall|here]]. For an example see [[Zone-policy_example|Zone-policy example]].

=== Groups ===

Firewall groups represent collections of IP addresses, networks, or ports.  Once created, a group can be referenced by firewall rules as either a source or destination.  Members can be added or removed from a group without changes to or the need to reload individual firewall rules.  Note that groups can also be referenced by NAT configuration.

While network groups accept IP networks in CIDR notation, specific IP addresses can be added as a 32-bit prefix.  If you foresee the need to add a mix of addresses and networks, the network group is recommended.

Here is an example of a network group for the IP networks that make up the internal network:

 set firewall group network-group NET-INSIDE network 192.168.0.0/24
 set firewall group network-group NET-INSIDE network 192.168.1.0/24

A port group represents only port numbers, not the protocol.  Port groups can be referenced for either TCP or UDP.  It is recommended that TCP and UDP groups are created separately to avoid accidentally filtering unnecessary ports.  Ranges of ports can be specified by using a <code>-</code>.

Here is an example of a port group a server:

 set firewall group port-group PORT-TCP-SERVER1 port 80
 set firewall group port-group PORT-TCP-SERVER1 port 443
 set firewall group port-group PORT-TCP-SERVER1 port 5000-5010

=== Rule-Sets ===

A rule-set is a named collection of firewall rules that can be applied to an interface or zone.  Each rule is numbered, has an action to apply if the rule is matched, and the ability to specify the criteria to match.

Example of a rule-set to filter traffic to the internal network:

 set firewall name INSIDE-OUT default-action drop
 set firewall name INSIDE-OUT rule 1010 action accept
 set firewall name INSIDE-OUT rule 1010 state established enable
 set firewall name INSIDE-OUT rule 1010 state related enable
 set firewall name INSIDE-OUT rule 1020 action drop
 set firewall name INSIDE-OUT rule 1020 state invalid enable

=== Applying a Rule-Set to an Interface ===

Once a rule-set is created, it can be applied to an interface.  Note only one rule-set can be applied to each interface for <code>in</code>, <code>out</code>, or <code>local</code> traffic for each protocol (IPv4 and IPv6).

 set interfaces ethernet eth1 firewall out name INSIDE-OUT

=== Applying a Rule-Set to a Zone ===

A named rule-set can also be applied to a zone relationship (note, zones must first be created):

 set zone-policy zone INSIDE from OUTSIDE firewall name INSIDE-OUT

=== Example Partial Config ===

 firewall {
    all-ping enable
    broadcast-ping disable
    config-trap disable
    group {
        network-group BAD-NETWORKS {
            network 1.2.3.0/24
            network 1.2.4.0/24
        }
        network-group GOOD-NETWORKS {
            network 4.5.6.0/24
            network 4.5.7.0/24
        }
        port-group BAD-PORTS {
            port 65535
        }
    }
    name FROM-INTERNET {
        default-action accept
        description "From the Internet"
        rule 10 {
            action accept
            description "Authorized Networks"
            protocol all
            source {
                group {
                    network-group GOOD-NETWORKS
                }
            }
        }
        rule 11 {
            action drop
            description "Bad Networks"
            protocol all
            source {
                group {
                    network-group BAD-NETWORKS
                }
            }
        }
        rule 30 {
            action drop
            description "BAD PORTS"
            destination {
                group {
                    port-group BAD-PORTS
                }
            }
            log enable
            protocol all
        }
    }
 }
 interfaces {
    ethernet eth1 {
        address dhcp
        description OUTSIDE
        duplex auto
        firewall {
            in {
                name FROM-INTERNET
            }
        }
    }
 }

[https://www.xfinity.com/support/internet/list-of-blocked-ports/ XFinity Blocked Port List]

== NAT ==
=== Source NAT  ===

Source NAT is typically referred to simply as NAT.  To be more correct, what most people refer to as NAT is actually the process of '''Port Address Translation (PAT)''', or '''NAT Overload''': The process of having many internal host systems communicate to the Internet using a single or subset of IP addresses.

To setup SNAT, we need to know:
* The internal IP addresses we want to translate
* The outgoing interface to perform the translation on
* The external IP address to translate to

In the example used for the Quick Start configuration above, we demonstrate the following configuration:

 set nat source rule 100 outbound-interface 'eth0'
 set nat source rule 100 source address '192.168.0.0/24'
 set nat source rule 100 translation address 'masquerade'

Which generates the following configuration:

 rule 100 {
     outbound-interface eth0
     source {
         address 192.168.0.0/24
     }
     translation {
         address masquerade
     }
 }

In this example, we use '''masquerade''' as the translation address instead of an IP address.  The '''masquerade''' target is effectively an alias to say "use whatever IP address is on the outgoing interface", rather than a statically configured IP address.  This is useful if you use DHCP for your outgoing interface and do not know what the external address will be.

When using NAT for a large number of host systems it recommended that a minimum of 1 IP address is used to NAT every 256 host systems.  This is due to the limit of 65,000 port numbers available for unique translations and a reserving an average of 200-300 sessions per host system.

Example: For an ~ 8,000 host network a source NAT pool of 32 IP addresses is recommended.

A pool of addresses can be defined by using a '''-''' in the '''set nat source rule [n] translation address''' statement.

 '''set nat source rule 100 translation address '203.0.113.32-203.0.113.63''''


<hr />

'''Note:''' Avoiding "Leaky" NAT

Linux netfilter will not NAT traffic marked as INVALID.  This often confuses people into thinking that Linux (or specifically VyOS) has a broken NAT implementation because non-NATed traffic is seen leaving an external interface.  This is actually working as intended, and a packet capture of the "leaky" traffic should reveal that the traffic is either an additional TCP "RST", "FIN,ACK", or "RST,ACK" sent by client systems after Linux netfilter considers the connection closed.  The most common is the additional TCP RST some host implementations send after terminating a connection (which is implementation-specific).

In other words, connection tracking has already observed the connection be closed and has transition the flow to INVALID to prevent attacks from attempting to reuse the connection.

You can avoid the "leaky" behavior by using a firewall policy that drops "invalid" state packets.

Having control over the matching of INVALID state traffic, e.g. the ability to selectively log, is an important troubleshooting tool for observing broken protocol behavior.  For this reason, VyOS does not globally drop invalid state traffic, instead allowing the operator to make the determination on how the traffic is handled.


<hr />

'''Note:''' Avoiding NAT breakage in the absence of split-DNS

A typical problem with using NAT and hosting public servers is the ability for internal systems to reach an internal server using it's external IP address.  The solution to this is usually the use of split-DNS to correctly point host systems to the internal address when requests are made internally.  Because many smaller networks lack DNS infrastructure, a work-around is commonly deployed to facilitate the traffic by NATing the request from internal hosts to the source address of the internal interface on the firewall.  This technique is commonly reffered to as '''NAT Reflection''', or '''Hairpin NAT'''.

In this example, we will be using the example Quick Start configuration above as a starting point.

To setup a NAT reflection rule, we need to create a rule to NAT connections from the internal network to the same internal network to use the source address of the internal interface.

 set nat source rule 110 description 'NAT Reflection: INSIDE'
 set nat source rule 110 destination address '192.168.0.0/24'
 set nat source rule 110 outbound-interface 'eth1'
 set nat source rule 110 source address '192.168.0.0/24'
 set nat source rule 110 translation address 'masquerade'

Which results in a configuration of:

 rule 110 {
     description "NAT Reflection: INSIDE"
     destination {
         address 192.168.0.0/24
     }
     outbound-interface eth1
     source {
         address 192.168.0.0/24
     }
     translation {
         address masquerade
     }
 }
<hr />

=== Destination NAT ===

DNAT is typically referred to as a '''Port Forward'''.  When using VyOS as a NAT router and firewall, a common configuration task is to redirect incoming traffic to a system behind the firewall.

In this example, we will be using the example Quick Start configuration above as a starting point.

To setup a destination NAT rule we need to gather:
* The interface traffic will be coming in on
* The protocol and port we wish to forward
* The IP address of the internal system we wish to forward traffic to

In our example, we will be forwarding web server traffic to an internal web server on 192.168.0.100.

HTTP traffic makes use of the TCP protocol on port 80.

For other common port numbers, see: [http://en.wikipedia.org/wiki/List_of_TCP_and_UDP_port_numbers]

Our configuration commands would be:

 set nat destination rule 10 description 'Port Forward: HTTP to 192.168.0.100'
 set nat destination rule 10 destination port '80'
 set nat destination rule 10 inbound-interface 'eth0'
 set nat destination rule 10 protocol 'tcp'
 set nat destination rule 10 translation address '192.168.0.100'

Which would generate the following NAT destination configuration:

 nat {
     destination {
         rule 10 {
             description "Port Forward: HTTP to 192.168.0.100"
             destination {
                 port 80
             }
             inbound-interface eth0
             protocol tcp
             translation {
                 address 192.168.0.100
             }
         }
     }
 }

Note that if forwarding traffic to a different port than it is arriving on, you may also configure the translation port using '''set nat destination rule [n] translation port'''.

This establishes our Port Forward rule, but if we created a firewall policy it will likely block the traffic.

It is important to note that when creating firewall rules that the DNAT translation occurs ''before'' traffic traverses the firewall.  In other words, the destination address has already been translated to 192.168.0.100.

So in our firewall policy, we want to allow traffic coming in on the outside interface, destined for TCP port 80 and the IP address of 192.168.0.100.

 set firewall name OUTSIDE-IN rule 20 action 'accept'
 set firewall name OUTSIDE-IN rule 20 destination address '192.168.0.100'
 set firewall name OUTSIDE-IN rule 20 destination port '80'
 set firewall name OUTSIDE-IN rule 20 protocol 'tcp'
 set firewall name OUTSIDE-IN rule 20 state new 'enable'

This would generate the following configuration:

 rule 20 {
     action accept
     destination {
         address 192.168.0.100
         port 80
     }
     protocol tcp
     state {
         new enable
     }
 }

'''Note''':  If you have configured the INSIDE-OUT policy, you will need to add additional rules to permit inbound NAT traffic.

=== 1-to-1 NAT ===

Another term often used for DNAT is '''1-to-1 NAT'''.

For a 1-to-1 NAT configuration, both DNAT and SNAT are used to NAT all traffic from an external IP address to an internal IP address and vice-versa.

Typically, a 1-to-1 NAT rule omits the destination port (all ports) and replaces the protocol with either '''all''' or '''ip'''.

Then a corresponding SNAT rule is created to NAT outgoing traffic for the internal IP to a reserved external IP.  This dedicates an external IP address to an internal IP address and is useful for protocols which don't have the notion of ports, such as GRE.

==== 1-to-1 NAT example ====

Here's an extract of a simple 1-to-1 NAT configuration with one internal and one external interface:

 set interfaces ethernet eth0 address '192.168.1.1/24'
 set interfaces ethernet eth0 description 'Inside interface'
 set interfaces ethernet eth1 address '1.2.3.4/24'
 set interfaces ethernet eth1 description 'Outside interface'
 set nat destination rule 2000 description '1-to-1 NAT example'
 set nat destination rule 2000 destination address '1.2.3.4'
 set nat destination rule 2000 inbound-interface 'eth1'
 set nat destination rule 2000 translation address '192.168.1.10'
 set nat source rule 2000 description '1-to-1 NAT example'
 set nat source rule 2000 outbound-interface 'eth1'
 set nat source rule 2000 source address '192.168.1.10'
 set nat source rule 2000 translation address '1.2.3.4'

Firewall rules are written as normal, using the internal IP address as the source of outbound rules and the destination of inbound rules.

=== NPTv6 (RFC6296) ===
See here : [[How_to_do_NPTv6]]

== VPN ==
=== OpenVPN ===
{{main|OpenVPN}}

Traditionally hardware routers implement IPsec exclusively due to relative ease of implementing it in hardware and insufficient CPU power for doing encryption in software. Since VyOS is a software router, this is less of a concern. OpenVPN has been widely used on UNIX platform for a long time and is a popular option for remote access VPN, though it's also capable of site-to-site connections.

The advantages of OpenVPN are:
* It uses a single TCP or UDP connection and does not rely on packet source addresses, so it will work even through a double NAT: perfect for public hotspots and such
* It's easy to setup and offers very flexible split tunneling
* There's a variety of client GUI frontends for any platform

The disadvantages are:
* It's slower than IPsec due to higher protocol overhead and the fact it runs in user mode while IPsec, on Linux, is in kernel mode
* None of the operating systems have client software installed by default

In the VyOS CLI, a key point often overlooked is that rather than being configured using the <code>set vpn</code> stanza, OpenVPN is configured as a network interface using <code>set interfaces openvpn</code>.

==== OpenVPN Site-To-Site ====

While many are aware of OpenVPN as a Client VPN solution, it is often overlooked as a site-to-site VPN solution due to lack of support for this mode in many router platforms.

Site-to-site mode supports x.509 but doesn't require it and can also work with static keys, which is simpler in many cases. In this example, we'll configure a simple site-to-site OpenVPN tunnel using a 2048-bit pre-shared key.

First, one one of the systems generate the key using the operational command <code>generate openvpn key <filename></code>.  This will generate a key with the name provided in the <code>/config/auth/</code> directory.  Once generated, you will need to copy this key to the remote router.

In our example, we used the filename <code>openvpn-1.key</code> which we will reference in our configuration.

* The public IP address of the local side of the VPN will be 198.51.100.10
* The remote will be 203.0.113.11
* The tunnel will use 10.255.1.1 for the local IP and 10.255.1.2 for the remote.
* OpenVPN allows for either TCP or UDP.  UDP will provide the lowest latency, while TCP will work better for lossy connections; generally UDP is preferred when possible.
* The official port for OpenVPN is 1194, which we reserve for client VPN; we will use 1195 for site-to-site VPN.
* The <code>persistent-tunnel</code> directive will allow us to configure tunnel-related attributes, such as firewall policy as we would on any normal network interface.
* If known, the IP of the remote router can be configured using the <code>remote-host</code> directive; if unknown, it can be omitted.  We will assume a dynamic IP for our remote router.

Local Configuration:

  set interfaces openvpn vtun1 mode site-to-site
  set interfaces openvpn vtun1 protocol udp
  set interfaces openvpn vtun1 persistent-tunnel
  set interfaces openvpn vtun1 local-host '198.51.100.10'
  set interfaces openvpn vtun1 local-port '1195'
  set interfaces openvpn vtun1 remote-port '1195'
  set interfaces openvpn vtun1 shared-secret-key-file '/config/auth/openvpn-1.key'
  set interfaces openvpn vtun1 local-address '10.255.1.1'
  set interfaces openvpn vtun1 remote-address '10.255.1.2'

Remote Configuration:

  set interfaces openvpn vtun1 mode site-to-site
  set interfaces openvpn vtun1 protocol udp
  set interfaces openvpn vtun1 persistent-tunnel
  set interfaces openvpn vtun1 remote-host '198.51.100.10'
  set interfaces openvpn vtun1 local-port '1195'
  set interfaces openvpn vtun1 remote-port '1195'
  set interfaces openvpn vtun1 shared-secret-key-file '/config/auth/openvpn-1.key'
  set interfaces openvpn vtun1 local-address '10.255.1.2'
  set interfaces openvpn vtun1 remote-address '10.255.1.1'

The configurations above will default to using 128-bit Blowfish in CBC mode for encryption and SHA-1 for HMAC authentication. These are both considered weak, but a number of other encryption and hashing algorithms are available:

For Encryption:

 vyos@vyos# set interfaces openvpn vtun1 encryption
 Possible completions:
   des          DES algorithm
   3des         DES algorithm with triple encryption
   bf128        Blowfish algorithm with 128-bit key
   bf256        Blowfish algorithm with 256-bit key
   aes128       AES algorithm with 128-bit key
   aes192       AES algorithm with 192-bit key
   aes256       AES algorithm with 256-bit key

For Hashing:

 vyos@vyos# set interfaces openvpn vtun1 hash
 Possible completions:
   md5          MD5 algorithm
   sha1         SHA-1 algorithm
   sha256       SHA-256 algorithm
   sha512       SHA-512 algorithm

If you change the default encryption and hashing algorithms, be sure that the local and remote ends have matching configurations, otherwise the tunnel will not come up.

Static routes can be configured referencing the tunnel interface; for example, the local router will use a network of 10.0.0.0/16, while the remote has a  network of 10.1.0.0/16:

Local Configuration:

  set protocols static interface-route 10.1.0.0/16 next-hop-interface vtun1

Remote Configuration:

  set protocols static interface-route 10.0.0.0/16 next-hop-interface vtun1

Firewall policy can also be applied to the tunnel interface for <code>local</code>, <code>in</code>, and <code>out</code> directions and function identically to ethernet interfaces.

If making use of multiple tunnels, OpenVPN must have a way to distinguish between different tunnels aside from the pre-shared-key.  This is either by referencing IP address or port number.  One option is to dedicate a public IP to each tunnel.  Another option is to dedicate a port number to each tunnel (e.g. 1195,1196,1197...)

OpenVPN status can be verified using the <code>show openvpn</code> operational commands.  See the built-in help for a complete list of options.

==== OpenVPN Server ====

Multi-client server is the most popular OpenVPN mode on routers. It always x.509 authentication and therefore requires a PKI setup. This guide assumes you have already setup a PKI and have a CA certificate, a server certificate and key, a certificate revokation list, a Diffie-Hellman key exchange parameters file. You do not need client certificates and keys for the server setup.

In this example we will use the most complicated case: a setup where each client is a router that has its own subnet (think HQ and branch offices), since simpler setups are subsets of it.

Suppose you want to use 10.23.1.0/24 network for client tunnel endpoints and all client subnets belong to 10.23.0.0/20. All clients need access to the 192.168.0.0/16 network.

First we need to specify the basic settings. 1194/UDP is the default. The persistent-tunnel option is recommended, it prevents the TUN/TAP device from closing on connection resets or daemon reloads.

<pre>
set interfaces openvpn vtun10 mode server
set interfaces openvpn vtun10 local-port 1194
set interfaces openvpn vtun10 persistent-tunnel
set interfaces openvpn vtun10 protocol udp
</pre>

Then we need to specify the location of the cryptographic materials. Suppose you keep the files in <code>/config/auth/openvpn</code>

<pre>
set interfaces openvpn vtun10 tls ca-cert-file /config/auth/openvpn/ca.crt
set interfaces openvpn vtun10 tls cert-file /config/auth/openvpn/server.crt
set interfaces openvpn vtun10 tls key-file /config/auth/openvpn/server.key
set interfaces openvpn vtun10 tls crl-file /config/auth/openvpn/crl.pem
set interfaces openvpn vtun10 tls dh-file /config/auth/openvpn/dh2048.pem
</pre>

Now we need to specify the server network settings. In all cases we need to specify the subnet for client tunnel endpoints. Since we want clients to access a specific network
behind out router, we will use a push-route option for installing that route on clients.

<pre>
set interfaces openvpn vtun10 server push-route 192.168.0.0/16
set interfaces openvpn vtun10 server subnet 10.23.1.0/24
</pre>

Since it's a HQ and branch offices setup, we will want all clients to have fixed addresses and we will route traffic to specific subnets through them.
We need configuration for each client to achieve this. Note that clients are identified by the CN field of their x.509 certificates, in this example the CN is client0:

<pre>
set interfaces openvpn vtun10 server client client0 ip 10.23.1.10
set interfaces openvpn vtun10 server client client0 subnet 10.23.2.0/25
</pre>

OpenVPN '''will not''' automatically create routes in the kernel for client subnets when they connect and will only use client-subnet association internally, so we need to create a route to the 10.23.0.0/20 network ourselves:
<pre>
set protocols static interface-route 10.23.0.0/20 next-hop-interface vtun10
</pre>

=== L2TP over IPsec ===
Example for configuring a simple L2TP over IPsec VPN for remote access (works with native Windows and Mac VPN clients):

 set vpn ipsec ipsec-interfaces interface eth0
 set vpn ipsec nat-traversal enable
 set vpn ipsec nat-networks allowed-network 0.0.0.0/0

 set vpn l2tp remote-access outside-address 203.0.113.2
 set vpn l2tp remote-access client-ip-pool start 192.168.255.1
 set vpn l2tp remote-access client-ip-pool stop 192.168.255.254
 set vpn l2tp remote-access ipsec-settings authentication mode pre-shared-secret
 set vpn l2tp remote-access ipsec-settings authentication pre-shared-secret <secret>
 set vpn l2tp remote-access authentication mode local
 set vpn l2tp remote-access authentication local-users username <username> password <password>

In the example above an external IP of 203.0.113.2 is assumed.

If a local firewall policy is in place on your external interface you will need to open:

* UDP port 500 (IKE)
* IP protocol number 50 (ESP)
* UDP port 1701 for IPsec

In addition when NAT is detected by the VPN client ESP is encapsulated in UDP for NAT-traversal:

* UDP port 4500 (NAT-T)

Example:

 set firewall name OUTSIDE-LOCAL rule 40 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 40 destination port '50'
 set firewall name OUTSIDE-LOCAL rule 40 protocol 'esp'
 set firewall name OUTSIDE-LOCAL rule 41 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 41 destination port '500'
 set firewall name OUTSIDE-LOCAL rule 41 protocol 'udp'
 set firewall name OUTSIDE-LOCAL rule 42 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 42 destination port '4500'
 set firewall name OUTSIDE-LOCAL rule 42 protocol 'udp'
 set firewall name OUTSIDE-LOCAL rule 43 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 43 destination port '1701'
 set firewall name OUTSIDE-LOCAL rule 43 ipsec 'match-ipsec'
 set firewall name OUTSIDE-LOCAL rule 43 protocol 'udp'

Also note that if you wish to allow the VPN to be used for external access you will need to add the appropriate source NAT rules to your configuration.

 set nat source rule 110 outbound-interface 'eth0'
 set nat source rule 110 source address '192.168.255.0/24'
 set nat source rule 110 translation address masquerade

To be able to resolve when connected to the VPN, the following DNS rules are needed as well.
 set vpn l2tp remote-access dns-servers server-1 '8.8.8.8'
 set vpn l2tp remote-access dns-servers server-2 '8.8.4.4'


Established sessions can be viewed using the '''show vpn remote-access''' operational command.

 vyos@vyos:~$ show vpn remote-access
 Active remote access VPN sessions:
 User            Proto Iface     Tunnel IP       TX byte RX byte  Time
 ----            ----- -----     ---------       ------- -------  ----
 vyos            L2TP  l2tp0     192.168.255.1      3.2K    8.0K  00h06m13s

=== Site-to-Site IPsec ===

Example:
* eth1 is WAN interface
* left subnet: 192.168.0.0/24 #s ite1, server side (i.e. locality, actually there is no client or server roles)
* left local_ip: 1.1.1.1 # server side WAN IP
* right subnet: 10.0.0.0/24  # site2,remote office side
* right local_ip: 2.2.2.2 # remote office side WAN IP

 # server side config
 set vpn ipsec esp-group office-srv-esp compression 'disable'
 set vpn ipsec esp-group office-srv-esp lifetime '1800'
 set vpn ipsec esp-group office-srv-esp mode 'tunnel'
 set vpn ipsec esp-group office-srv-esp pfs 'enable'
 set vpn ipsec esp-group office-srv-esp proposal 1 encryption 'aes256'
 set vpn ipsec esp-group office-srv-esp proposal 1 hash 'sha1'
 set vpn ipsec ike-group office-srv-ike ikev2-reauth 'no'
 set vpn ipsec ike-group office-srv-ike key-exchange 'ikev1'
 set vpn ipsec ike-group office-srv-ike lifetime '3600'
 set vpn ipsec ike-group office-srv-ike proposal 1 encryption 'aes256'
 set vpn ipsec ike-group office-srv-ike proposal 1 hash 'sha1'
 set vpn ipsec ipsec-interfaces interface 'eth1'
 set vpn ipsec site-to-site peer 2.2.2.2 authentication mode 'pre-shared-secret'
 set vpn ipsec site-to-site peer 2.2.2.2 authentication pre-shared-secret 'SomePreSharedKey'
 set vpn ipsec site-to-site peer 2.2.2.2 ike-group 'office-srv-ike'
 set vpn ipsec site-to-site peer 2.2.2.2 local-address '1.1.1.1'
 set vpn ipsec site-to-site peer 2.2.2.2 tunnel 0 allow-nat-networks 'disable'
 set vpn ipsec site-to-site peer 2.2.2.2 tunnel 0 allow-public-networks 'disable'
 set vpn ipsec site-to-site peer 2.2.2.2 tunnel 0 esp-group 'office-srv-esp'
 set vpn ipsec site-to-site peer 2.2.2.2 tunnel 0 local prefix '192.168.0.0/24'
 set vpn ipsec site-to-site peer 2.2.2.2 tunnel 0 remote prefix '10.0.0.0/21'

 # remote office side config
 set vpn ipsec esp-group office-srv-esp compression 'disable'
 set vpn ipsec esp-group office-srv-esp lifetime '1800'
 set vpn ipsec esp-group office-srv-esp mode 'tunnel'
 set vpn ipsec esp-group office-srv-esp pfs 'enable'
 set vpn ipsec esp-group office-srv-esp proposal 1 encryption 'aes256'
 set vpn ipsec esp-group office-srv-esp proposal 1 hash 'sha1'
 set vpn ipsec ike-group office-srv-ike ikev2-reauth 'no'
 set vpn ipsec ike-group office-srv-ike key-exchange 'ikev1'
 set vpn ipsec ike-group office-srv-ike lifetime '3600'
 set vpn ipsec ike-group office-srv-ike proposal 1 encryption 'aes256'
 set vpn ipsec ike-group office-srv-ike proposal 1 hash 'sha1'
 set vpn ipsec ipsec-interfaces interface 'eth1'
 set vpn ipsec site-to-site peer 1.1.1.1 authentication mode 'pre-shared-secret'
 set vpn ipsec site-to-site peer 1.1.1.1 authentication pre-shared-secret 'SomePreSharedKey'
 set vpn ipsec site-to-site peer 1.1.1.1 ike-group 'office-srv-ike'
 set vpn ipsec site-to-site peer 1.1.1.1 local-address '2.2.2.2'
 set vpn ipsec site-to-site peer 1.1.1.1 tunnel 0 allow-nat-networks 'disable'
 set vpn ipsec site-to-site peer 1.1.1.1 tunnel 0 allow-public-networks 'disable'
 set vpn ipsec site-to-site peer 1.1.1.1 tunnel 0 esp-group 'office-srv-esp'
 set vpn ipsec site-to-site peer 1.1.1.1 tunnel 0 local prefix '10.0.0.0/21'
 set vpn ipsec site-to-site peer 1.1.1.1 tunnel 0 remote prefix '192.168.0.0/24'

 vyos@srv-gw0:~$ show vpn ike sa
 Peer ID / IP                            Local ID / IP
 ------------                            -------------
 2.2.2.2                                 1.1.1.1
    State  Encrypt  Hash    D-H Grp  NAT-T  A-Time  L-Time
    -----  -------  ----    -------  -----  ------  ------
    up     aes256   sha1    5        no     734     3600


 vyos@srv-gw0:~$ show vpn ipsec sa
 Peer ID / IP                            Local ID / IP
 ------------                            -------------
 2.2.2.2                                 1.1.1.1
    Tunnel  State  Bytes Out/In   Encrypt  Hash    NAT-T  A-Time  L-Time  Proto
    ------  -----  -------------  -------  ----    -----  ------  ------  -----
    0       up     7.5M/230.6K    aes256   sha1    no     567     1800    all

If there is SNAT rules on eth1, need to add exclude rule

 # server side
 set nat source rule 10 destination address '10.0.0.0/24'
 set nat source rule 10 'exclude'
 set nat source rule 10 outbound-interface 'eth1'
 set nat source rule 10 source address '192.168.0.0/24'

 # remote office side
 set nat source rule 10 destination address '192.168.0.0/24'
 set nat source rule 10 'exclude'
 set nat source rule 10 outbound-interface 'eth1'
 set nat source rule 10 source address '10.0.0.0/24'

To allow traffic to pass through to clients, you need to add the following rules. (if you used the default configuration at the top of this page)

 # server side
 set firewall name OUTSIDE-LOCAL rule 32 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 32 source address '10.0.0.0/24'

 # remote office side
 set firewall name OUTSIDE-LOCAL rule 32 action 'accept'
 set firewall name OUTSIDE-LOCAL rule 32 source address '192.168.0.0/24'

=== DMVPN ===

Advanced DMVPN configuration examples are available on the [[DMVPN]] page.

== QoS and Traffic Policy ==

The traffic policy subsystem provides an interface to Linux traffic control.

One common use of traffic policy is to limit bandwidth for an interface.  In the example below we limit bandwidth for our LAN connection to 200M download and out WAN connection to 50M upload:

 set traffic-policy shaper WAN-OUT bandwidth '50Mbit'
 set traffic-policy shaper WAN-OUT default bandwidth '50%'
 set traffic-policy shaper WAN-OUT default ceiling '100%'
 set traffic-policy shaper WAN-OUT default queue-type 'fair-queue'

 set traffic-policy shaper LAN-OUT bandwidth '200Mbit'
 set traffic-policy shaper LAN-OUT default bandwidth '50%'
 set traffic-policy shaper LAN-OUT default ceiling '100%'
 set traffic-policy shaper LAN-OUT default queue-type 'fair-queue'

Resulting in the following configuration:

 traffic-policy {
     shaper WAN-OUT {
         bandwidth 50Mbit
         default {
             bandwidth 50%
             ceiling 100%
             queue-type fair-queue
         }
     }
     shaper LAN-OUT {
         bandwidth 200Mbit
         default {
             bandwidth 50%
             ceiling 100%
             queue-type fair-queue
         }
     }
 }

Once defined, a traffic policy can be applied to each interface using the interface-level <code>traffic-policy</code> directive:

 set interfaces ethernet eth0 traffic-policy out 'WAN-OUT'
 set interfaces ethernet eth1 traffic-policy out 'LAN-OUT'

Note that a traffic policy can also be defined to match specific traffic flows using class statements.

VyOS also supports HFSC (included in [[Lithium]]).

 set traffic-policy shaper-hfsc

See further information on the [[QoS]] page.

== DHCP Server ==

''For more information, refer to the [[DHCP server]] page.''

VyOS provides a DHCP server. The following example provides open pool addressing for a LAN network:

VyOS < 1.2.0
 set service dhcp-server shared-network-name 'LAN' authoritative enable
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' start '192.168.0.128' stop '192.168.0.254'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' default-router '192.168.0.1'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' dns-server '192.168.0.1'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' domain-name 'internal-net'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' lease 86400

VyOS >= 1.2.0

Multiple ranges can be defined and can contain holes.
 set service dhcp-server shared-network-name 'LAN' authoritative
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' range 0 start '192.168.0.128'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' range 0 stop '192.168.0.254'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' default-router '192.168.0.1'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' dns-server '192.168.0.1'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' domain-name 'internal-net'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' lease 86400

This will provide dynamic addressing using a 24-hour lease and the range of 128-254 for host addressing, reserving the first half of the network for static assignment.  Note that the DHCP service will NOT be authoritative for the subnet unless explicitly configured.

Static mappings can also be configured for hosts which need a fixed address via DHCP:

 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' static-mapping 'SERVER' ip-address '192.168.0.10'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' static-mapping 'SERVER' mac-address '00:53:00:00:00:01'

=== Failover ===

VyOS provides support for DHCP failover:

 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover local-address '192.168.0.1'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover name 'foo'
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover peer-address '192.168.0.2'

<b>NOTE:</b> <code>name</code> must be identical on both sides!

The primary and secondary statements determines whether the server is primary or secondary
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover status 'primary'
or
 set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover status 'secondary'

=== DHCPv6 server ===

DHCPv6 server shares most of the configuration options with IPv4 DHCP, with one major exception: in IPv6, DHCP is never used for default gateway configuration.
If default gateway is configured automatically, it is always done via router advertisment (RA).

Since router advertisment cannot be deactivated even if DHCPv6 is in use, first you need to set the "managed flag" in RA, which instructs clients
to request an IPv6 address via DHCPv6 instead of using SLAAC or EUI-64.

<pre>
set interfaces ethernet eth1 address '2001:db8:ff::1/64'
set interfaces ethernet eth1 ipv6 router-advert managed-flag 'true'
</pre>

Then you can setup DHCPv6 server:

<pre>
set service dhcpv6-server shared-network-name LAN subnet 2001:db8:ff::/64 address-range prefix '2001:db8:ff::/64'
set service dhcpv6-server shared-network-name LAN subnet 2001:db8:ff::/64 address-range start 2001:db8::1000 stop '2001:db8::ffff'
set service dhcpv6-server shared-network-name LAN subnet 2001:db8:ff::/64 name-server '2001:db8:aa::bb'
</pre>

== DHCP-Relay ==

VyOS can act as a DHCP relay, sending DHCP requests from locally connected networks to a central DHCP server, or servers:

 set service dhcp-relay interface eth0
 set service dhcp-relay interface eth1
 set service dhcp-relay server 192.168.0.4
 set service dhcp-relay server 192.168.0.5

An important note that dhcp-relay currently requires specifying the interface the DHCP server replies come from in addition to interfaces to listen on.  An upstream bug exists for this: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=648401

By default the ISC dhcp-relay process will relay relay packets; as this is not expected behavior, disabling this functionality is recommended using the following directive:

  set service dhcp-relay relay-options relay-agents-packets discard

Additional protections can be configured matching <code>hop-limit</code> and <code>max-size</code> for DHCP packets.

  set service dhcp-relay hop-count 10
  set service dhcp-relay max-size 576

== DNS Forwarder ==

VyOS provides a DNS forwarder.  This example shows the forwarder being used to listen for DNS request on interface eth1 and use Google Public DNS for name servers with caching disabled:

  set service dns forwarding name-server 8.8.8.8
  set service dns forwarding name-server 8.8.4.4
  set service dns forwarding cache-size 0
  set service dns forwarding listen-on eth1

Alternatively, DNS servers can be specified to be the system DNS servers using the <code>set service dns forwarding system</code> directive, or to those obtained via DHCP using the <code>[...] dhcp <interface></code> directive.

By default, the forwarder will also make use of the local hosts on the system; this can be disable using the <code>ignore-host-file</code> directive.

To add entries to the local hosts file for the system, the <code>set system static-host-mapping</code> directive can be used:

  set system static-host-mapping host-name example.com inet 127.0.0.1

== Dynamic DNS ==
VyOS provides a dynamic DNS update agent which can be used to update DNS providers when dynamic addressing is used.

 set service dns dynamic interface eth0

More information here : [[Dynamic_DNS]]

== mDNS Repeater ==
VyOS (1.2.x) provides a Multicast DNS repeater functionality.

Multicast DNS uses the 224.0.0.51 address, which is "administratively scoped" and does not leave the subnet. It re-broadcast mDNS packets from one interface to other interfaces. This enables support for e.g. Airplay devices across multiple VLANs.

 set service mdns repeater interface eth0
 set service mdns repeater interface eth1

Will re-broadcast all mDNS packets from <code>eth0</code> to <code>eth1</code> and vice versa.

mDNS repeater can be disabled using <code>set service mdns repeater disable</code>

== UDP broadcast relay ==
Certain vendors use broadcasts to identify their equipemnt within one ethernet segment. Unfortunately if you split your network with multiple VLANs you loose the ability of identifying your equiment. This is where "UDP broadcast relay" comes into work. It will forward received broadcasts to other configured networks.

Every UDP port which will be forward requires one unique ID. Currently we support 99 IDs!

<b>Forward broadcasts on port 1900 for eth3, eth4 and eth5</b>
 set service broadcast-relay id 1 description 'SONOS'
 set service broadcast-relay id 1 interface 'eth3'
 set service broadcast-relay id 1 interface 'eth4'
 set service broadcast-relay id 1 interface 'eth5'
 set service broadcast-relay id 1 port '1900'

<b>Forward broadcasts on port 6969 for eth3, eth4</b>
 set service broadcast-relay id 2 description 'SONOS MGMT'
 set service broadcast-relay id 2 interface 'eth3'
 set service broadcast-relay id 2 interface 'eth4'
 set service broadcast-relay id 2 port '6969'

Each broadcast relay instance can be disabled using <code>set service broadcast-relay id <n> disable</code>.

In addition you can disable the whole service without removing the configuration by <code>set service broadcast-relay disable</code>.


== System Configuration ==

=== System Users ===

As of 1.1.8 release and 1.2.0 release candidates, VyOS support two user privilege levels: admin and operator.
However, the operator level is a legacy feature and was proved insecure: any user can escape the restricted shell in multiple easy way. That feature will be removed in future releases, and we do not recommend using it.


==== Creating Login User Accounts ====

Create user account jsmith, with admin level access and the password "mypassword"

 set system login user jsmith full-name "Johan Smith"
 set system login user jsmith authentication plaintext-password mypassword
 commit

The command:

 show system login

will show the contents of the <code>system login</code> configuration node:

 user jsmith {
     authentication {
         encrypted-password $6$0OQHjuQ8M$AYXVn7jufdfqPrSk4/XXsDBw99JBtNsETkQKDgVLptXogHA2bU9BWlvViOFPBoFxIi.iqjqrvsQdQ./cfiiPT.
         plaintext-password ""
     }
     full-name "Johan Smith"
     level admin
 }

==== Configuring for SSH Access using Shared Public Keys ====

The following command will load the public key dev.pub for user jsmith

 loadkey jsmith dev.pub

'''Note:''' this requires uploading the dev.pub public key to the vyos firewall first. As an alternative you can also load the ssh public key directly from a remote system:

 loadkey jsmith scp://devuser@dev001.vyos.net/home/devuser/.ssh/dev.pub

== IPv6 ==

Advanced IPv6 configuration examples are available on the [[IPv6]] page.

== Clustering ==

VyOS supports multicast and unicast clustering.  Multicast is default and to use the unicast method you can add the peer directive to the interface with the ip of the other cluster member.

In the example below SSH is clustered between two nodes with the unicast method.

 cluster {
   dead-interval 20000
   group cluster {
     auto-failback false
     primary vyos
     secondary vyos2
     service ssh
     service 192.168.0.123/24/eth0
   }
   interface eth0 {
     peer 192.168.0.121
   }
   keepalive-interval 5000
   monitor-dead-interval 20000
   pre-shared-secret S3cr#t
 }

== System Image Management ==

The VyOS image-based installation is implemented by creating a directory for each image on the storage device selected during the install process.

The directory structure of the boot device:

  /
  /boot
  /boot/grub
  /boot/VyOS_999.hydrogen.11291501

The image directory contains the system kernel, a compressed image of the root filesystem for the OS, and a directory for persistent storage, such as configuration.

On boot, the system will extract the OS image into memory and mount the appropriate live-rw sub-directories to provide persistent storage system configuration.

This process allows for a system to always boot to a known working state, as the OS image is fixed and non-persistent.  It also allows for multiple releases of VyOS to be installed on the same storage device.

The image can be selected manually at boot if needed, but the system will otherwise boot the image configured to be the default.

The default boot image can be set using the '''set system image default-boot''' command in operational mode.

A list of available images can be shown using the '''show system image''' command in operational mode.

 vyos@vyos:~$ '''show system image'''
 The system currently has the following image(s) installed:

    1: 999.hydrogen.12130649 (default boot) (running image)
    2: 999.hydrogen.12100644

 vyos@vyos:~$

Images no longer needed can be removed using the '''delete system image''' command.

Finally, new system images can be added using the '''add system image''' command.  The add image command will extract the image from the release ISO (either on the local filesystem or remotely if a URL is provided).  The image install process will prompt you to use the current system configuration and SSH security keys, allowing for the new image to boot using the current configuration.

Note that configuration is associated to each image, and each image has a unique copy of its configuration.  This is different than a traditional network router where the configuration is shared across all images.

If you need some files from a previous images - take a look inside a /live directory.

== Troubleshooting ==
Sometimes things break or don't work as expected. This section describes several troubleshooting tools provided by VyOS that can help when something goes wrong.

=== Basic Connectivity Verification ===
Verifying connectivity can be done with the familiar '''ping''' and '''traceroute''' commands. The options for each are shown (the options for each command were displayed using the built-in help as described in the [[#Using_the_Command-Line_Interface|Using the Command-Line Interface]] section and are omitted from the output here):

 vyos@vyos:~$ ping
 Possible completions:
  <hostname>    Send Internet Control Message Protocol (ICMP) echo request
  <x.x.x.x>
  <h:h:h:h:h:h:h:h>
 vyos@vyos:~$

Several options are available when more extensive troubleshooting is needed:

 vyos@vyos:~$ ping 8.8.8.8
 Possible completions:
  <Enter>       Execute the current command
  adaptive      Ping options
  allow-broadcast
  audible
  bypass-route
  count
  deadline
  flood
  interface
  interval
  mark
  no-loopback
  numeric
  pattern
  quiet
  record-route
  size
  timestamp
  tos
  ttl
  verbose
 vyos@vyos:~$

 vyos@vyos:~$ traceroute
 Possible completions:
  <hostname>    Track network path to specified node
  <x.x.x.x>
  <h:h:h:h:h:h:h:h>
  ipv4          Track network path to <hostname|IPv4 address>
  ipv6          Track network path to <hostname|IPv6 address>
 vyos@vyos:~$

However, another tool, '''mtr''', is available which combines ping and traceroute into a single tool. An example of its output is shown:

 vyos@vyos:~$ mtr 10.62.212.12

The output of '''mtr''' consumes the screen and will replace your command prompt:

                                        My traceroute  [v0.75]
 vyos (0.0.0.0)                                                                         Fri Feb 24 14:28:08 2017
 Keys:  Help   Display mode   Restart statistics   Order of fields   quit
                                                                              Packets               Pings
 Host                                                                 Loss%   Snt   Last   Avg  Best  Wrst StDev
 1. 10.11.110.4                                                       0.0%    34    0.5   0.5   0.4   0.8   0.1
 2. 10.62.255.184                                                     0.0%    34    1.1   1.0   0.9   1.4   0.1
 3. 10.62.255.71                                                      0.0%    34    1.4   1.4   1.3   2.0   0.1
 4. 10.62.212.12                                                      0.0%    34    1.6   1.6   1.6   1.7   0.0

Several options are available for changing the display output. Press '''h''' to invoke the built in help system. To quit, just press '''q''' and you'll be returned to the VyOS command prompt.

=== Monitoring Network Interfaces ===
It's possible to monitor network traffic, either at the flow level or protocol level. This can be useful when troubleshooting a variety of protocols and configurations. The following interface types can be monitored:

 vyos@vyos:~$ monitor interfaces
 Possible completions:
  <Enter>       Execute the current command
  bonding       Monitor a bonding interface
  bridge        Monitor a bridge interface
  ethernet      Monitor a ethernet interface
  loopback      Monitor a loopback interface
  openvpn       Monitor an openvpn interface
  pppoe         Monitor pppoe interface
  pseudo-ethernet
                Monitor a pseudo-ethernet interface
  tunnel        Monitor a tunnel interface
  vrrp          Monitor a vrrp interface
  vti           Monitor a vti interface
  wireless      Monitor wireless interface
 vyos@vyos:~$

To monitor traffic flows, issue the '''monitor interfaces <type> <name> flow''' command, replacing '''<type>''' and '''<name>''' with your desired interface type and name, respectively. Output looks like the following:

                    12.5Kb              25.0Kb              37.5Kb              50.0Kb        62.5Kb
 ????????????????????????????????????????????????????????????????????????????????????????????????????
 10.11.111.255                        => 10.11.110.37                            0b      0b      0b
                                     <=                                       624b    749b    749b
 10.11.110.29                         => 10.62.200.11                            0b    198b    198b
                                     <=                                         0b    356b    356b
 255.255.255.255                      => 10.11.110.47                            0b      0b      0b
                                     <=                                       724b    145b    145b
 10.11.111.255                        => 10.11.110.47                            0b      0b      0b
                                     <=                                       724b    145b    145b
 10.11.111.255                        => 10.11.110.255                           0b      0b      0b
                                     <=                                       680b    136b    136b
 ????????????????????????????????????????????????????????????????????????????????????????????????????
 TX:             cumm:  26.7KB   peak:   40.6Kb                      rates:   23.2Kb  21.4Kb  21.4Kb
 RX:                    67.5KB           63.6Kb                               54.6Kb  54.0Kb  54.0Kb
 TOTAL:                 94.2KB            104Kb                               77.8Kb  75.4Kb  75.4Kb

Several options are available for changing the display output. Press '''h''' to invoke the built in help system. To quit, just press '''q''' and you'll be returned to the VyOS command prompt.

To monitor interface traffic, issue the '''monitor interfaces <type> <name> traffic''' command, replacing '''<type>''' and '''<name>''' with your desired interface type and name, respectively. This command invokes the familiar '''tshark''' utility and the following options are available:

 vyos@vyos:~$ monitor interfaces ethernet eth0 traffic
 Possible completions:
  <Enter>       Execute the current command
  detail        Monitor detailed traffic for the specified ethernet interface
  filter        Monitor filtered traffic for the specified ethernet interface
  save          Save monitored traffic to a file
  unlimited     Monitor traffic for the specified ethernet interface
 vyos@vyos:~$

To quit monitoring, press '''Ctrl-c''' and you'll be returned to the VyOS command prompt. The '''detail''' keyword provides verbose output of the traffic seen on the monitored interface. The '''filter''' keyword accepts valid [http://www.tcpdump.org/manpages/pcap-filter.7.html PCAP filter expressions], enclosed in single or double quotes (e.g. <nowiki>'port 25'</nowiki> or <nowiki>"port 161 and udp"</nowiki>). The '''save''' keyword allows you to save the traffic dump to a file. The '''unlimited''' keyword is used to specify that an unlimited number of packets can be captured (by default, 1,000 packets are captured and you're returned to the VyOS command prompt).


[[Category: User documentation]]



==Referensi==

* https://wiki.vyos.net/wiki/User_Guide#Route_Filtering


==Pranala Menarik==

* [[IPv6]]
* [[IPv6: VyOS]]