View source for OpenBTS: 2.8 Konfigurasi Cognitive Radio Elsabagh

Sumber: http://wush.net/svn/range/software/public/openbts/features/Cognitive_Radio_Elsabagh/apps/OpenBTS.config.example

 # Sample OpenBTS configuration file.


 # Formatting rules:
 
 # Configuration values are defined with line of the form <key><space><value>
 # The key name can contain no spaces.
 # Everything between the first space and the end of the line becomes the value.
 # Numeric values can be preceded with "0x" for hex.
 
 # Blank lines are OK.
 
 # Lines starting with "#" are comments.
 
 # By default, configuration values can be changed but not removed after initialization.
 
 # Lines starting with "$" are directives that define other properties of config values:
 # "static" --  configuration value cannot be changed or removed after initialization.
 # "optional" -- configuration value may be removed after initialization.


 # As a gerenal rule, non-valid configuration values will crash OpenBTS.
 # So be cafeful.


 #
 # Logging and reporting parameters
 #
 
 # The initial global logging level: ERROR, WARN, NOTICE, INFO, DEBUG, DEEPDEBUG
 Log.Level NOTICE
 # Logging levels can also be defined for individual source files.
 # This example set shows normal operations in the control layer (L3).
 Log.Level.MobilityManagement.cpp INFO
 $optional Log.Level.MobilityManagement.cpp
 Log.Level.CallControl.cpp INFO
 $optional Log.Level.CallControl.cpp
 Log.Level.RadioResource.cpp INFO
 $optional Log.Level.RadioResource.cpp

 # The log file path.  If not set, logging goes to stdout.
 Log.FileName test.out
 $static Log.FileName

 # LOG(ALARM) is printed and also sent as udp to this address.
 Log.Alarms.TargetIP 192.168.10.200
 $optional Log.Alarms.TargetIP
 Log.Alarms.TargetPort 10101
 # Number of alarms saved in internal queue
 Log.Alarms.Max 10

 # Wireshark support
 # OpenBTS writes L2 GSMTAP messages to this port.
 # If GSMTAP.TargetIP is not defined, this output is disabled.
 GSMTAP.TargetIP 127.0.0.1
 $optional GSMTAP.TargetIP
 # The standard IANA for GSMTAP is 4729.  This can be used to override that.
 #GSMTAP.TargetPort 4729

 # Indications port
 # Some interal operations produce status reports sent to this port.
 # This can be the same as the Alarm target.
 Indications.TargetIP 127.0.0.1
 Indications.TargetPort 10202


 # Port number for test calls.
 # This is where an external program can interact with a handset via UDP.
 TestCall.Port 28670


 #
 # Transceiver parameters
 #

 # Transceiver interface
 # This TRX.IP is not really adjustable.  Just leave it as 127.0.0.1.
 TRX.IP 127.0.0.1
 $static TRX.IP
 # This value is hard-coded in the transcevier.  Just leave it alone.
 TRX.Port 5700
 $static TRX.Port

 # Path to transceiver binary
 # If this is not defined, you will need to start the transceiver by hand.
 # YOU MUST HAVE A MATCHING libusrp AS WELL!!
 TRX.Path ../Transceiver/transceiver
 #TRX.Path ../Transceiver52M/transceiver
 $static TRX.Path

 # TRX logging.
 # Logging level.
 # IF TRX.Path IS DEFINED, THIS MUST ALSO BE DEFINED.
 TRX.LogLevel NOTICE
 $static TRX.LogLevel
 # Logging file.  If not defined, logs to stdout.
 TRX.LogFileName test.TRX.out
 $static TRX.LogFileName



 #
 # SIP, RTP, servers
 #

 # Asterisk PBX
 Asterisk.IP 127.0.0.1
 Asterisk.Port 5060
 $static Asterisk.IP
 $static Asterisk.Port

 # Messaging server
 Smqueue.IP 127.0.0.1
 Smqueue.Port 5063
 $static Smqueue.IP
 $static Smqueue.Port

 # Local SIP/RTP ports
 # OpenBTS binds to these ports.
 SIP.Port 5062
 $static SIP.Port
 RTP.Start 16484
 RTP.Range 98
 $static RTP.Start
 $static RTP.Range

 # If Asterisk is 127.0.0.1, this is also 127.0.0.1.
 # Otherwise, this should be the local IP address of the interface used to contact  asterisk.
 # In other words, this is the IP address at which Asterisk will see OpenBTS.
 SIP.IP 127.0.0.1



 #
 # Special extensions.
 #

 #  Routing extension for emergency calls.
 #  This must be defined, even if you are not supporting emergency calls.
 PBX.Emergency 2101


 #
 # SIP parameters
 #

 # SIP registration period in seconds.
 # Ideally, this should be slightly longer than GSM.T3212.
 SIP.RegistrationPeriod 7200

 #
 # SIP Internal Timers.  All timer values are given in millseconds.
 # These are from RFC-3261 Table A.
 #

 # SIP Timer A, the INVITE retry period, RFC-3261 Section 17.1.1.2
 # in milliseconds
 # For fast SMS interactions, keep this at 2000 or more.
 SIP.Timer.A 2000



 #
 # SMS parameters
 #
 # ISDN address of source SMSC when we fake out a source SMSC.
 SMS.FakeSrcSMSC 0000
 # ISDN address of destination SMSC when a fake value is needed.
 SMS.DefaultDestSMSC 0000


 # The SMS HTTP gateway.
 # Comment out if you don't have one or if you want to use smqueue.
 #SMS.HTTP.Gateway api.clickatell.com

 # IF SMS.HTTP.Gateway IS DEFINED, SMS.HTTP.AccessString MUST ALSO BE DEFINED.
 #SMS.HTTP.AccessString sendmsg?user=xxxx&password=xxxx&api_id=xxxx




 # Things to query during registration updates.
 #Control.LUR.QueryIMEI
 $optional Control.LUR.QueryIMEI
 #Control.LUR.QueryClassmark
 $optional Control.LUR.QueryClassmark

 # Does everyone get a TMSI, registered or not?
 Control.LUR.TMSIsAll
 $optional Control.LUR.TMSIsAll

 # TMSI table controls

 # Maximum number of TMSIs to track
 Control.TMSITable.MaxSize 10000

 # Maximum allowed ages of a TMSI, in hours.
 Control.TMSITable.MaxAge 72

 # Want persistent TMSIs?
 Control.TMSITable.SavePath TMSITable.txt
 $optional Control.TMSISavePath



 # Open Registration and Self-Provisioning
 # If this is defined, the network accepts LUR from unprovisioned handsets.
 # This is required to support SMS-based auto-provisioning.
 # This is a boolean -- either defined or not.
 Control.OpenRegistration
 $optional Control.OpenRegistration


 #
 # "Welcome" messages sent during IMSI attach attempts.
 # ANY WELCOME MESSAGE MUST BE LESS THAN 138 CHARACTERS.
 # ANY DEFINED WELCOME MESSAGE MUST ALSO HAVE A DEFINED SHORT CODE.
 # Comment out any message you don't want to use.
 #

 # The message sent upon full successful registration, all the way through the Asterisk  server .
 # THIS MESSAGE IS NORMALLY REQUIRED FOR COMPLIANCE WITH AGPLv3.
 Control.NormalRegistrationWelcomeMessage Welcome to OpenBTS! AGPLv3 openbts.sf.net. Your IMSI is
 Control.NormalRegistrationWelcomeShortCode 0000

 # Then message sent to accpeted open registrations.
 # IF OPEN REGISTRATION IS ENABLED, THIS MUST ALSO BE DEFINED.
 # THIS MESSAGE IS NORMALLY REQUIRED FOR COMPLIANCE WITH AGPLv3.
 Control.OpenRegistrationWelcomeMessage Welcome to OpenBTS! AGPLv3 openbts.sf.net. Your IMSI is
 # If you use SMS auto-provisioning, use that short code as the return address here.
 Control.OpenRegistrationWelcomeShortCode 101

 # Then message send to failed registrations.
 #Control.FailedRegistrationWelcomeMessage Your handset is not provisioned for this network.
 $optional Control.FailedRegistrationWelcomeMessage
 Control.FailedRegistrationWelcomeShortCode 1000




 #
 # GSM
 #

 # Network and cell identity.

 # Network Color Code, 0-7
 # Also set GSM.NCCsPermitted later in this file.
 GSM.NCC 0
 # Basesation Color Code, 0-7
 GSM.BCC 2
 # Mobile Country Code, 3 digits.
 # MCC MUST BE 3 DIGITS.  Prefix with 0s if needed.
 # Test code is 001.
 GSM.MCC 001
 # Mobile Network Code, 2 or 3 digits.
 # Test code is 01.
 GSM.MNC 01
 # Location Area Code, 0-65535
 GSM.LAC 1000
 # Cell ID, 0-65535
 GSM.CI 10

 # Network "short name" to display on the handset.
 # This is optional, but must be defined if you also want to
 # send current time-of-day to the phine.
 GSM.ShortName OpenBTS
 $optional GSM.ShortName

 # A boolean telling whether or not to show country initials with the name.
 GSM.ShowCountry
 $optional GMS.ShowCountry

 # Assignment type for call setup.
 # The default is early assignment.
 # If defined, this will cause us to use very early assignment instead.
 #GSM.VEA
 $optional GSM.VEA

 # Band and Frequency

 # Valid band values are 850, 900, 1800, 1900.
 GSM.Band 900
 $static GSM.Band

 # Valid ARFCN range depends on the band.
 GSM.ARFCN 51 
 # ARCN 975 is inside the US ISM-900 band and also in the GSM900 band.
 #GSM.ARFCN 975
 # ARFCN 207 was what we ran at BM2008, I think, in the GSM850 band.
 #GSM.ARFCN 207
 $static GSM.ARFCN

 # Neighbor list
 # Should probably include our own ARFCN
 GSM.Neighbors 39 41 43
 #GSM.Neighbors 207


 # Expected environmental delay spread, in symbols, at about 1.1 km/sym.
 # FIXME -- Should be a TRX parameter.
 GSM.MaxExpectedDelaySpread 1 
 # Receiver Gain, in dB
 # comment out to set receiver to maximum possible receive gain
 # With RxGain 57, -71.0dBm <-> 0dB RSSI, -113dBm <-> -38.2dB RSSI, -120dBm <-> -41.4dB RSSI
 # With RxGain 47, -57.4dBm <-> 0dB RSSI, -113dBm <-> -51.3dB RSSI, -120dBm <-> -54.5dB RSSI
 # With RxGain 37, -43.6dBm <-> 0dB RSSI, -113dBm <-> -63.1dB RSSI, -120dBm <-> -65.4dB RSSI
 GSM.RxGain 47


 # Downlink adaptive power management.
 # Manages power to prevent congestion.

 # Downlink tx power level bounds, dB wrt full power
 # For the Mk 1B 900:
 # Output power of USRP is 20 dBm at full scale.
 # We installed a 10 dB attenuator.
 # Gain of HPA-900 is 40 dB.
 # So the output power, in dBm, is Po = 20 + 40 - 10 - Atten = 50 - Atten.
 # So Atten = 50 - Po.
 # That has been verified on the CMD57.
 # HPA-900 max ouput is 42 dBm: Atten = 50 - 42 = 8 dB.
 # Balanced link at 33 dBm: Atten = 50 - 33 = 17 dB.
 # Maximum attenuation (sets MINIMUM power level).
 # Atten 30 -> 20 dBm.
 GSM.PowerManager.MaxAttenDB 30 
 # Minimum attenuation (sets MAXIMUM power level).
 # Atten 7 -> 36 dBm. (with TX IF of 40MHz)
 GSM.PowerManager.MinAttenDB  7 

 # Target T3122 for Power Manager.
 # Under heavy load, the power manager will adjust downlink power
 # so that T3122 meets this taret.
 # THE TARGET T3122 MUST BE BETWEEN THE MIN AND MAX VALUES.
 # THOSE ARE SET SOMEWHERE ELSE IN THIS FILE, GSM.T3122Max, GSM.T3122Min.
 GSM.PowerManager.TargetT3122 5000
 # T3122 sampling period, in milliseconds.
 # PowerMananger.SamplePeriod should be <= PowerMananger.Period.
 GSM.PowerManager.SamplePeriod 2000
 # Sample history for averaging T3122, MUST BE <100;
 GSM.PowerManager.NumSamples 10
 # Power manager adaptation step period, in milliseconds
 # Should be >= PowerMananger.SamplePeriod
 GSM.PowerManager.Period 6000


 # Channel configuration
 # Number of C-VII slots (8xSDCCH)
 GSM.NumC7s 1
 $static GSM.NumC7s
 # Number of C-I slots (1xTCH/F)
 GSM.NumC1s 6
 $static GSM.NumC1s
 # Half-duplex option for low-capacity on cheap hardware.
 #GSM.HalfDuplex
 $optional GSM.HalfDuplex
 #$static GSM.HalfDuplex



 # Beacon parameters.

 # L1 radio link timeout advertised on BCCH.
 # This is the RAW parameter sent on the BCCH.
 # See GSM 10.5.2.3 for encoding.
 # Value of 15 gives 64-frame timeout, about 30 seconds on the TCH.
 # This should be coordinated with T3109.
 GSM.RADIO_LINK_TIMEOUT 15

 # Control Channel Description (CCD)

 # Attach/detach flag.
 # Set to 1 to use attach/detach procedure, 0 otherwise.
 # This will make initial LUR more prompt.
 # It will also cause an un-regstration if the handset powers off
 # and really head LUR loads in areas with spotty coverage.
 GSM.CCD.ATT 1

 # CCCH_CONF
 # See GSM 10.5.2.11 for encoding.
 # Value of 1 means we are using a C-V beacon.
 GSM.CCD.CCCH_CONF 1

 # RACH Parameters

 # Maximum RACH retransmission attempts
 # This is the RAW parameter sent on the BCCH.
 # See GSM 04.08 10.5.2.29 for encoding.
 GSM.RACH.MaxRetrans 1

 # Parameter to spread RACH busts over time.
 # This is the RAW parameter sent on the BCCH.
 # See GSM 04.08 10.5.2.29 for encoding.
 GSM.RACH.TxInteger 14

 # Access class flags.
 # This is the RAW parameter sent on the BCCH.
 # See GSM 04.08 10.5.2.29 for encoding.
 # Set to 0 to allow full access.
 # Set to 0x0400 to indicate no support for emergency calls.
 GSM.RACH.AC 0

 # NCCs Permitted.
 # An 8-bit mask of allowed NCCs.
 # Unless you are coordinating with another carrier,
 # this should probably just select your own NCC.
 GSM.NCCsPermitted 1

 # Cell Selection Parameters (CS)
 GSM.CS.MS_TXPWR_MAX_CCH 0
 GSM.CS.RXLEV_ACCESS_MIN 0

 # Cell Reselection Hysteresis
 # See GSM 04.08 10.5.2.4, Table 10.5.23 for encoding.
 # Encoding is 2N dB, value values of N are 0..7 for 0..14 dB.
 GSM.CS.CELL_RESELECT_HYSTERESIS 3

 # NECI, New Establishment Causes
 # This should be set to "1" if you want to support very early assignment.
 # See GSM 04.08 10.5.2.4, Table 10.5.23 and 04.08 9.1.8, Table 9.9.
 GSM.CS.NECI 1


 # Reject cause for location updating failures
 # Reject causes come from GSM 04.08 10.5.3.6
 # Reject cause 0x04, IMSI not in VLR
 GSM.LURejectCause 0x04



 #
 # Parameters for MS adaptive power and timing.
 #

 # Maximum timing advance.
 # Can be used to control the range of the BTS.
 # The unit is GSM symbols of round trips delay, about 550 meters per symbol.
 # If you set this <1 or >63, you can break things.
 GSM.MS.TA.Max 5
 # Adaptation damping factor, scaled up by 100.
 # The larger this is, the smoother (and less responsive) the adaptation.
 # The valie range is 0..100.
 GSM.MS.TA.Damping 50

 # Maximum and minimum MS tx power, given in dBm.
 # The meaningful MS tx power range is 5-33 dBm.
 GSM.MS.Power.Max 33
 GSM.MS.Power.Min 5
 # Adaptation damping factor, scaled up by 100.
 # The larger this is, the smoother (and less responsive) the adaptation.
 # The valie range is 0..100.
 GSM.MS.Power.Damping 50




 #
 # GSM Timers.  All timer values are given in milliseconds unless stated otherwise.
 # These come from GSM 04.08 11.2.
 #

 # T3212, registration timer.
 # Unlike most timers, this is given in MINUTES.
 # Actual period will be rounded down to a multiple of 6 minutes.
 # Any value below 6 minutes disables periodic registration, which is probably a bad idea.
 # Valid range is 6..1530.
 # Ideally, this should be slightly less than the SIP.RegistrationPeriod.
 GSM.T3212 12

 # T3122, RACH holdoff timer.
 # This value can vary internally between the min and max ends of the range.
 # When congestion occurs, T3122 grows exponentially.
 GSM.T3122Min 2000
 # T3211Max MUST BE NO MORE THAN 255 s.
 GSM.T3122Max 255000

 # T3113, the paging timer
 # This is the time allowed for a handset to respond to a paging request.
 GSM.T3113 10000


 # RRLP

 # RRLP query conditions
 # These booleans just have to be defined.  The actual values don't matter.
 #GSM.RRLP.LUR
 #$optional GSM.RRLP.LUR
 #GSM.RRLP.MOC
 #$optional GSM.RRLP.MOC
 #GSM.RRLP.MTC
 #$optional GSM.RRLP.MTC
 #GSM.RRLP.MOSMS
 #$optional GSM.RRLP.MOSMS
 #GSM.RRLP.MTSMS
 #$optional GSM.RRLP.MTSMS

 # Accuracy requested from MS - 60 is about 400m (scale is approx. logarithmic)
 GSM.RRLP.Accuracy 60
 # Number of requests done per RRLPQueryController::doTransaction
 GSM.RRLP.Retries 1
 # RRLP query timeout, ms
 GSM.RRLP.Timeout 4000

 # The maximum AGCH queue length.
 GSM.AGCH.QMax 5

 # The uplink RSSI target for closed loop power control.
 # For a "naked" USRP, this should be around -15 dB.
 GSM.RSSITarget -15

 # Number of channels reserved for paging responses.
 # This is useful to insure paging response bandwidth when LUR loads are very high,
 # but for most applications should just be zero.
 GSM.PagingReservations 0

 # Maximum internal FIFO latency, in vocoder frames.
 # Trade-off is dropped frames vs. delay.
 GSM.MaxSpeechLatency 2

 #
 # CLI paramters
 #

 CLI.Prompt OpenBTS> 










==Referensi==

* http://wush.net/svn/range/software/public/openbts/features/Cognitive_Radio_Elsabagh/apps/OpenBTS.config.example



==Pranala Menarik==

* [[OpenBTS]]
* [[OpenBTS: Arsitektur secara umum]]

===Persiapan===

* [[USRP: High Precision Clock]]
* [[USRP: Menyambungkan ClockTamer ke USRP1]]
* [[USRP: Kalibrasi ClockTamer]]
* [[USRP: ClockTamer Control Protocol]]
* [[USRP: Instalasi Board]]
* [[OpenBTS: GIT Source Code]]
* [[USRP: Rangkaian Board USRP]]
* [[OpenBTS: Tethr untuk Bencana Alam]]
* [[USRP: Tip Pemesanan]]

===OpenBTS 2.6===

* [[GNURadio]]
* [[GNURadio: Ubuntu Install]]
* [[GNURadio: Menggunakan UHD]]
* [[GNURadio: Ubuntu Install GNURadio 3.4.2]] '''RECOMMENDED'''
* [[GNURadio: Ubuntu Install GNURadio 3.4.2 Clock 52MHz]] '''RECOMMENDED'''
* [[GNURadio: Ubuntu 13.04 Install GNURadio 3.4.2 Clock 52MHz]] ''NOT RECOMMENDED''
* [[GNURadio: Contoh Aplikasi]]
* [[GNURadio: Spectrum Analizer GSM]]
* [[GNURadio: Mengubah board RFX1800 menjadi RFX900]]
* [[GNURadio: Programming Untuk Pemula]]
* [[OpenBTS: Ubuntu Install]] '''RECOMMENDED'''
* [[OpenBTS: Ubuntu Install OpenBTS 2.6 Clock 52MHz]] '''RECOMMENDED'''
* [[OpenBTS: Ubuntu 13.04 Install OpenBTS 2.6 Clock 52MHz]] ''NOT RECOMMENDED''
* [[OpenBTS: Konfigurasi]] '''RECOMMENDED'''
* [[OpenBTS: Kalibrasi]]
* [[OpenBTS: Konfigurasi Asterisk untuk OpenBTS]] '''RECOMMENDED'''
* [[OpenBTS: Menjalankan smqueue]]
* [[OpenBTS: Mengoperasikan BTS]] '''RECOMMENDED'''
* [[OpenBTS: Tampilan di Nokia saat pakai OpenBTS]]
* [[OpenBTS: Operasi 1800 MHz]]
* [[OpenBTS: Beberapa Tips]]
* [[OpenBTS: USRP2]]
* [[OpenBTS: Amplifier]]
* [[OpenBTS: SMS]]
* [[AirProbe]]

===OpenBTS 2.8===

* [[GNURadio: Ubuntu 11.10 Install]] ''NOT RECOMMENED''
* [[GNURadio: Ubuntu 11.10 instalasi menggunakan Repo]] ''NOT RECOMMENDED''
* [[GNURadio: Download GNURadio]]
* [[GNURadio: Install UHD]]
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.3.0]]
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.3.0]]
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.4.1]] ''NOT RECOMMENDED''
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
* [[GNURadio: Ubuntu 12.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
* [[GNURadio: Ubuntu 12.04.1 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.4.2]] ''NOT RECOMMENDED''
* [[GNURadio: Ubuntu 13.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.0]] ''NOT RECOMMENDED''
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.3.2]] ''NOT RECOMMENDED''
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.6.0]] ''NOT RECOMMENDED''
* [[GNURadio: Ubuntu 11.10 Install dari GIT GNURadio]] ''NOT RECOMMENDED''
* [[GNURadio: Ubuntu 11.10 cek USRP Daughter Board]]
* [[GNURadio: UHD]] ''NOT RECOMMENDED''
* [[GNURadio: UHD Image]] ''NOT RECOMMENDED''
* [[GNURadio: UHD burn EEPROM RFX Board di USRP1]] ''NOT RECOMMENDED''
* [[GNURadio: UHD Identifikasi Device]]
* [[OpenBTS: Ubuntu 11.10 Install]]
* [[OpenBTS: dari GIT ttsou]]
* [[OpenBTS: 2.8 dari SVN Install]]
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz]] '''RECOMMENDED'''
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz di Ubuntu 12.10]] '''RECOMMENDED'''
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz di Ubuntu 13.04]] '''RECOMMENDED'''
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz dengan UHD tanpa GNURadio]] ''NOT RECOMMENDED''
* [[OpenBTS: 2.8 Edit User di sqlite3.db]] '''RECOMMEND'''
* [[OpenBTS: Yate Softswitch]] '''RECOMMENDED'''
* [[OpenBTS: Yate Softswitch install Ubuntu 12.10]] '''RECOMMENDED'''
* [[OpenBTS: Yate Softswitch install Ubuntu 13.04]] '''RECOMMENDED'''
* [[OpenBTS: Yate Config Test]]
* [[OpenBTS: 2.8 Instalasi Real Time Asterisk]] '''RECOMMENDED'''
* [[OpenBTS: 2.8 Menjalankan]] '''RECOMMENDED'''
* [[OpenBTS: 2.8 Konfigurasi]]
* [[OpenBTS: 2.8 Konfigurasi Cognitive Radio Elsabagh]]
* [[OpenBTS: 2.8 Konfigurasi Subscriber Registery]]
* [[OpenBTS: Database SQLite]]

===Multi OpenBTS 2.8===

* [[OpenBTS: Pola Multi OpenBTS]] '''RECOMMENDED'''
* [[Multi OpenBTS: Catatan Konfigurasi]] '''RECOMMENDED'''

===Ettus E110===

* [[OpenBTS: E110 Cara Login]]
* [[OpenBTS: E110 Install Image di MicroSD]] '''*RECOMMENDED*'''
* [[OpenBTS: E110 Cek Daughter Board]]
* [[OpenBTS: E110 Mengubah Master Clock]]
* [[OpenBTS: E110 Kalibrasi Clock]]
* [[OpenBTS: E110 Konfigurasi Jaringan]]
* [[OpenBTS: E110 Bekerja dengan opkg]]
* [[OpenBTS: E110 Instalasi iptables]]
* [[OpenBTS: E110 GNURadio]]
* [[OpenBTS: E110 Compile UHD]] ''Not Recommended''
* [[OpenBTS: E110 Compile UHD dari Release Bukan git]] ''Not Recommended''
* [[OpenBTS: E110 UHD burn EEPROM RFX Board]] ''Not Recommended''
* [[OpenBTS: E110 Install UHD Image]] ''Not Recommended''
* [[OpenBTS: E110 Instalasi OpenBTS]]
* [[OpenBTS: E110 Instalasi OpenBTS 2.6]] ''NOT RECOMMENDED''
* [[OpenBTS: E110 Instalasi OpenBTS 2.8 untuk MultiBTS]] '''*RECOMMENDED*'''
* [[OpenBTS: E110 Yate Softswitch]]

===Ettus N210===

* [[OpenBTS: N210 Instalasi GPSDO Kit]]
* [[OpenBTS: N210 GNURadio]]
* [[OpenBTS: N210 GNURadio 3.7.0]]
* [[OpenBTS: N210 Instalasi OpenBTS]]
* [[OpenBTS: N210 Instalasi Yate]]
* [[OpenBTS: N210 Yate Config Test]]
* [[OpenBTS: N210 Burn Firmware]]

===GPRS===

* [[OpenBTS: GPRS]]
* [[OpenBTS: GPRS Konfigurasi]]

===Briker OpenBTS===

* [[OpenBTS: Briker]]

===FreeSWITCH OpenBTS===

* [[OpenBTS: FreeSWITCH]]

===Power Amplifier===

* [[Driver 900MHz]]
* [[Power Amplifier 900MHz]]
* [[Duplexer]]
* [[OpenBTS: Menaikan Jangkauan OpenBTS]]

===Lain Lain===

* [[OpenBTS: Materi Magang di ICTWATCH]]
* [[OpenBTS: Seminar Outline]]
* [[OpenBTS: Workshop Outline]]
* [[Membuat Base Station GSM Open Source]]
* [[Teknologi Selular]]
* [[GSM: Daftar Channel Frekuensi]]
* [[Wireless Internet]]
* [[OpenBSC]]
* [[AirProbe]]
* [[Base station subsystem]]
* [[GSM]]
* [[Asterisk]]
* [[Mobile phone]]

===Catatan Legal dan Pendukung===

* [[Siapa Bilang OpenBTS Ilegal?]]
* [[OpenBTS: Catatan MNC dan MCC Indonesia]]
* [[OpenBTS: Catatan MNC dan MCC COOL]]
* [[OpenBTS : Alokasi Frekuensi Operator GSM Indonesia]]
* [[GSM: Daftar Channel Frekuensi]]

===Catatan Sejarah===

* [[2011/04/30 - Workshop OpenBTS Pertama di Indonesia dilakukan di Univ Gajah Putih Takengon Aceh Tengah]]
* [[OpenBTS: Daftar Workshop atau Seminar yang pernah dilakukan]]
* [[OpenBTS: Daftar Artikel di Media]]
* [[OpenBTS: Permohonan Kanal dan DID untuk OpenBTS]]
* [[OpenBTS: 2013/02/19 - OpenBTS TelkomSel Mengudara di Muscat Oman]]

===Dokumentasi Video===

* http://www.metrotvnews.com/read/newsprograms/2012/10/14/14624/212/Teknologi-BTS
* http://youtu.be/8ogOcUSpINU (1/6)
* http://youtu.be/F5d7HGuhppk (2/6)
* http://youtu.be/90Jgq6bOgrQ (3/6)
* http://youtu.be/cNkx_qNqdfc (4/6)
* http://youtu.be/6LCuoeI57ak (5/6)
* http://youtu.be/-dEqcHoIlYk (6/6)

[[Category: Wireless]]
[[Category: Selular]]