Onnowpurbo at 03:46, 5 January 2016

2016-01-05T03:46:02Z

← Older revision		Revision as of 03:46, 5 January 2016
Line 1:		Line 1:
	Sumber: Arduino Motor Shield (L293)		Sumber: http://www.dfrobot.com/wiki/index.php/Arduino_Shield Arduino Motor Shield (L293)

	Introduction		Introduction
Line 107:		Line 107:
	==Referensi==		==Referensi==

	* Arduino Motor Shield (L293)		* http://www.dfrobot.com/wiki/index.php/Arduino_Shield Arduino Motor Shield (L293)

Onnowpurbo at 03:45, 5 January 2016

2016-01-05T03:45:03Z

Show changes

Onnowpurbo: New page: Sumber: Arduino Motor Shield (L293) Introduction This motor shield allows Arduino to drive two channel DC motors. It uses a L293B chip which deliveries output current up to 1A (2A for L2...

2016-01-05T03:42:33Z

New page: Sumber: Arduino Motor Shield (L293) Introduction This motor shield allows Arduino to drive two channel DC motors. It uses a L293B chip which deliveries output current up to 1A (2A for L2...

New page

Sumber: Arduino Motor Shield (L293)

Introduction

This motor shield allows Arduino to drive two channel DC motors. It uses a L293B chip which deliveries output current up to 1A (2A for L298P version) each channel. The speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6. The enable/disable function of the motor control is signalled by Arduino Digital Pin 4 and 7. Roboduino Motor Shield uses PWM output Pin 6 and 9 and Digital Pin 7 and 8.

The Motor shield is powered directly from Arduino. It is strongly advised that use external power supply to power the Arduino instead of the USB power supply.

==Code==

//This motor shield use Pin 6,5,7,4 to control the motor
// Simply connect your motors to M1+,M1-,M2+,M2-
// Upload the code to Arduino/Roboduino
// Through serial monitor, type 'a','s', 'w','d','x' to control the motor
// www.dfrobot.com
// Last modified on 24/12/2009

int EN1 = 6;
int EN2 = 5; //Roboduino Motor shield uses Pin 9
int IN1 = 7;
int IN2 = 4; //Latest version use pin 4 instead of pin 8

void Motor1(int pwm, boolean reverse)
{
analogWrite(EN1,pwm); //set pwm control, 0 for stop, and 255 for maximum speed
if(reverse)
{
digitalWrite(IN1,HIGH);
}
else
{
digitalWrite(IN1,LOW);
}
}

void Motor2(int pwm, boolean reverse)
{
analogWrite(EN2,pwm);
if(reverse)
{
digitalWrite(IN2,HIGH);
}
else
{
digitalWrite(IN2,LOW);
}
}

void setup()
{
int i;
// for(i=6;i<=9;i++) //For Roboduino Motor Shield
// pinMode(i, OUTPUT); //set pin 6,7,8,9 to output mode

for(i=5;i<=8;i++) //For Arduino Motor Shield
pinMode(i, OUTPUT); //set pin 4,5,6,7 to output mode

Serial.begin(9600);
}

void loop()
{
int x,delay_en;
char val;
while(1)
{
val = Serial.read();
if(val!=-1)
{
switch(val)
{
case 'w'://Move ahead
Motor1(100,true); //You can change the speed, such as Motor(50,true)
Motor2(100,true);

break;
case 'x'://move back
Motor1(100,false);
Motor2(100,false);
break;
case 'a'://turn left
Motor1(100,false);
Motor2(100,true);
break;
case 'd'://turn right
Motor1(100,true);
Motor2(100,false);
break;
case 's'://stop
Motor1(0,false);
Motor2(0,false);
break;

}

}

}
}

==Referensi==

* Arduino Motor Shield (L293)

Arduino: Arduino Motor Shield (L293) - Revision history

Onnowpurbo at 03:46, 5 January 2016

Onnowpurbo at 03:45, 5 January 2016

Onnowpurbo: New page: Sumber: Arduino Motor Shield (L293) Introduction This motor shield allows Arduino to drive two channel DC motors. It uses a L293B chip which deliveries output current up to 1A (2A for L2...