Arduino: Ethernet TCP telnet client - Revision history

Onnowpurbo at 06:07, 23 February 2016

2016-02-23T06:07:04Z

← Older revision		Revision as of 06:07, 23 February 2016
Line 98:		Line 98:

	nc -l 10002		nc -l 10002


			==Sisi Client==

			Di Arduino, komunikasi dapat dilakukan dengan

			* Serial Monitor
			* Ctrl-Shift-M


	==Referensi==		==Referensi==

	* https://www.arduino.cc/en/Tutorial/TelnetClient		* https://www.arduino.cc/en/Tutorial/TelnetClient

Onnowpurbo: /* Sisi Server */

2016-02-23T06:06:37Z

Sisi Server

← Older revision		Revision as of 06:06, 23 February 2016
Line 98:		Line 98:

	nc -l 10002		nc -l 10002

	~~Komunikasi dapat dilakukan dengan~~

	* Serial Monitor
	* Ctrl-Shift-M

	==Referensi==		==Referensi==

	* https://www.arduino.cc/en/Tutorial/TelnetClient		* https://www.arduino.cc/en/Tutorial/TelnetClient

Onnowpurbo: /* Sisi Server */

2016-02-23T06:06:22Z

Sisi Server

← Older revision		Revision as of 06:06, 23 February 2016
Line 99:		Line 99:
	nc -l 10002		nc -l 10002

			Komunikasi dapat dilakukan dengan

			* Serial Monitor
			* Ctrl-Shift-M

	==Referensi==		==Referensi==

	* https://www.arduino.cc/en/Tutorial/TelnetClient		* https://www.arduino.cc/en/Tutorial/TelnetClient

Onnowpurbo at 06:04, 23 February 2016

2016-02-23T06:04:38Z

← Older revision		Revision as of 06:04, 23 February 2016
Line 91:		Line 91:
	}		}
	}		}


			==Sisi Server==

			Menggunakan Ubuntu 14.04

			nc -l 10002


	==Referensi==		==Referensi==

	* https://www.arduino.cc/en/Tutorial/TelnetClient		* https://www.arduino.cc/en/Tutorial/TelnetClient

Onnowpurbo: /* Code */

2016-02-23T06:00:57Z

Code

← Older revision		Revision as of 06:00, 23 February 2016
Line 36:		Line 36:
	// Enter the IP address of the server you're connecting to:		// Enter the IP address of the server you're connecting to:
	IPAddress server(192, 168, 0, 100);		IPAddress server(192, 168, 0, 100);

	// Initialize the Ethernet client library		// Initialize the Ethernet client library
	// with the IP address and port of the server		// with the IP address and port of the server
Line 91:		Line 91:
	}		}
	}		}



	==Referensi==		==Referensi==

	* https://www.arduino.cc/en/Tutorial/TelnetClient		* https://www.arduino.cc/en/Tutorial/TelnetClient

Onnowpurbo: New page: Sumber: https://www.arduino.cc/en/Tutorial/TelnetClient ==Code== /* Telnet client This sketch connects to a a telnet server (http://www.google.com) using an Arduino Wiznet Eth...

2016-02-23T05:09:46Z

New page: Sumber: https://www.arduino.cc/en/Tutorial/TelnetClient ==Code== /* Telnet client This sketch connects to a a telnet server (http://www.google.com) using an Arduino Wiznet Eth...

New page

Sumber: https://www.arduino.cc/en/Tutorial/TelnetClient

==Code==

/*
Telnet client

This sketch connects to a a telnet server (http://www.google.com)
using an Arduino Wiznet Ethernet shield. You'll need a telnet server
to test this with.
Processing's ChatServer example (part of the network library) works well,
running on port 10002. It can be found as part of the examples
in the Processing application, available at
http://processing.org/

Circuit:
* Ethernet shield attached to pins 10, 11, 12, 13

created 14 Sep 2010
modified 9 Apr 2012
by Tom Igoe

*/

#include <SPI.h>
#include <Ethernet.h>

// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
};
IPAddress ip(192, 168, 0, 4);

// Enter the IP address of the server you're connecting to:
IPAddress server(192, 168, 0, 100);

// Initialize the Ethernet client library
// with the IP address and port of the server
// that you want to connect to (port 23 is default for telnet;
// if you're using Processing's ChatServer, use port 10002):
EthernetClient client;

void setup() {
// start the Ethernet connection:
Ethernet.begin(mac, ip);
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for native USB port only
}

// give the Ethernet shield a second to initialize:
delay(1000);
Serial.println("connecting...");

// if you get a connection, report back via serial:
if (client.connect(server, 10002)) {
Serial.println("connected");
} else {
// if you didn't get a connection to the server:
Serial.println("connection failed");
}
}

void loop() {
// if there are incoming bytes available
// from the server, read them and print them:
if (client.available()) {
char c = client.read();
Serial.print(c);
}

// as long as there are bytes in the serial queue,
// read them and send them out the socket if it's open:
while (Serial.available() > 0) {
char inChar = Serial.read();
if (client.connected()) {
client.print(inChar);
}
}

// if the server's disconnected, stop the client:
if (!client.connected()) {
Serial.println();
Serial.println("disconnecting.");
client.stop();
// do nothing:
while (true);
}
}

==Referensi==

* https://www.arduino.cc/en/Tutorial/TelnetClient