Network Bonding di Ubuntu - Revision history

Unknown user at 11:01, 26 February 2022

2022-02-26T11:01:12Z

← Older revision		Revision as of 11:01, 26 February 2022
Line 6:		Line 6:
	2) apt-get install ifenslave		2) apt-get install ifenslave
	3) edit /etc/network/interfaces as follows		3) edit /etc/network/interfaces as follows
	~~# The loopback network interface~~
	~~auto lo~~
	~~iface lo inet loopback~~

	auto ~~bond0~~		# The loopback network interface
	iface ~~bond0~~ inet ~~static~~		auto lo
	~~# change the next three lines according to actual network settings~~		iface lo inet loopback
	~~address 192.168.1.200~~
	~~gateway 192.168.1.1~~
	~~netmask 255.255.255.0~~

	slaves eth0 eth1		auto bond0
	bond-mode balance-rr		iface bond0 inet static
	bond-miimon 100		# change the next three lines according to actual network settings
	bond-primary eth0 eth1		address 192.168.1.200
	up /sbin/ifenslave bond0 eth0 eth1		gateway 192.168.1.1
	down /sbin/ifenslave -d bond0 eth0 eth1		netmask 255.255.255.0
			slaves eth0 eth1
			bond-mode balance-rr
			bond-miimon 100
			bond-primary eth0 eth1
			up /sbin/ifenslave bond0 eth0 eth1
			down /sbin/ifenslave -d bond0 eth0 eth1

	4) either do a complete system reboot or the following:		4) either do a complete system reboot or the following:
	a) /etc/inti.d/networking restart
	b) ifconfig eth0 0 (and ignore the error, this [ and the next ] command will delete what ever ip address that eth0 has been originally set to)		a) /etc/inti.d/networking restart
	c) ifconfig eth1 0		b) ifconfig eth0 0 (and ignore the error, this [ and the next ] command will delete what ever ip address that eth0 has been originally set to)
	d) adjust the routes if necessary, mostly the default route needs to be replaced (change to via bond0 instead of eth0 or eth1, for example:		c) ifconfig eth1 0
	route del default dev eth0		d) adjust the routes if necessary, mostly the default route needs to be replaced (change to via bond0 instead of eth0 or eth1, for example:

			route del default dev eth0
	or		or
	route del default dev eth1		route del default dev eth1
	)		)

Onnowpurbo: /* Pranala Menarik */

2012-12-05T05:25:49Z

Pranala Menarik

← Older revision		Revision as of 05:25, 5 December 2012
Line 47:		Line 47:
	* [[Linux Howto Network Bonding]]		* [[Linux Howto Network Bonding]]
	* [[Network Bonding di Ubuntu]]		* [[Network Bonding di Ubuntu]]
			* [[Ubuntu Bonding Network Interface]]

Onnowpurbo: /* Pranala Menarik */

2012-12-05T05:22:07Z

Pranala Menarik

← Older revision		Revision as of 05:22, 5 December 2012
Line 43:		Line 43:

	==Pranala Menarik==		==Pranala Menarik==

			* [[Konfigurasi Networking Bonding]]
			* [[Linux Howto Network Bonding]]
			* [[Network Bonding di Ubuntu]]

Onnowpurbo: New page: Ethernet bonding howto in Ubuntu 10.10 January 9, 2011ricoch3nLeave a commentGo to comments Tested in 64bit environment. 1) echo “alias bond0 bonding” > /etc/modprobe.d/bonding.conf 2...

2012-12-05T05:21:52Z

New page: Ethernet bonding howto in Ubuntu 10.10 January 9, 2011ricoch3nLeave a commentGo to comments Tested in 64bit environment. 1) echo “alias bond0 bonding” > /etc/modprobe.d/bonding.conf 2...

New page

Ethernet bonding howto in Ubuntu 10.10
January 9, 2011ricoch3nLeave a commentGo to comments
Tested in 64bit environment.

1) echo “alias bond0 bonding” > /etc/modprobe.d/bonding.conf
2) apt-get install ifenslave
3) edit /etc/network/interfaces as follows
# The loopback network interface
auto lo
iface lo inet loopback

auto bond0
iface bond0 inet static
# change the next three lines according to actual network settings
address 192.168.1.200
gateway 192.168.1.1
netmask 255.255.255.0

slaves eth0 eth1
bond-mode balance-rr
bond-miimon 100
bond-primary eth0 eth1
up /sbin/ifenslave bond0 eth0 eth1
down /sbin/ifenslave -d bond0 eth0 eth1

4) either do a complete system reboot or the following:
a) /etc/inti.d/networking restart
b) ifconfig eth0 0 (and ignore the error, this [ and the next ] command will delete what ever ip address that eth0 has been originally set to)
c) ifconfig eth1 0
d) adjust the routes if necessary, mostly the default route needs to be replaced (change to via bond0 instead of eth0 or eth1, for example:
route del default dev eth0
or
route del default dev eth1
)

Regardless which method is chosen in step 4, it’s usually safer to change the network setting through a local console instead of a remote ssh session.

Source: https://help.ubuntu.com/community/UbuntuBonding

==Referensi==

* http://ricochen.wordpress.com/2011/01/09/ethernet-bonding-howto-in-ubuntu-10-10/

==Pranala Menarik==