OpenBTS: RangeNetwork Hardware - Revision history

Onnowpurbo: /* Referensi */

2019-05-08T00:20:01Z

Referensi

← Older revision		Revision as of 00:20, 8 May 2019
Line 23:		Line 23:

	* https://github.com/RangeNetworks/hardware-designs		* https://github.com/RangeNetworks/hardware-designs


			==Pranala Menarik==

			* [[OpenBTS]]

Onnowpurbo at 00:19, 8 May 2019

2019-05-08T00:19:29Z

← Older revision		Revision as of 00:19, 8 May 2019
Line 4:		Line 4:

	Range Networks SDR1 terdiri dari dua PCB yang bekerja bersama-sama, disebut sebagai modul SDR dan modul RF. Modul SDR menyediakan pemrosesan sinyal dan transfer data digital antara sinyal RF dan host. Modul RF menyediakan transmisi wireless untuk komunikasi data. Board modul SDR dan RF masing-masing memiliki ukuran PCB 5,5 inchi x 3,25 inchi. Ini adalah desain bertumpuk dengan konektor antarmuka tunggal di antara mereka. Modul RF menggunakan tata letak PCB yang sama dengan opsi isian komponen yang berbeda dan mampu mendukung pita frekuensi berikut: 850, 900, 1800, 1900 MHz. SDR1 sebagian besar didasarkan pada desain USRP1.		Range Networks SDR1 terdiri dari dua PCB yang bekerja bersama-sama, disebut sebagai modul SDR dan modul RF. Modul SDR menyediakan pemrosesan sinyal dan transfer data digital antara sinyal RF dan host. Modul RF menyediakan transmisi wireless untuk komunikasi data. Board modul SDR dan RF masing-masing memiliki ukuran PCB 5,5 inchi x 3,25 inchi. Ini adalah desain bertumpuk dengan konektor antarmuka tunggal di antara mereka. Modul RF menggunakan tata letak PCB yang sama dengan opsi isian komponen yang berbeda dan mampu mendukung pita frekuensi berikut: 850, 900, 1800, 1900 MHz. SDR1 sebagian besar didasarkan pada desain USRP1.


	~~The design resources provided are as follows:~~

	~~Software-defined radio (SDR) module~~
	~~Schematics in pdf format~~
	~~BOM in text format~~
	~~Gerber files with assembly and fabrication drawings~~
	~~NVM file for Silicon Labs Si5332C OTP eeprom~~
	~~RF module~~
	~~Schematics in pdf format~~
	~~BOM in text format: Low band and High band~~
	~~Gerber files with assembly and fabrication drawings~~

Onnowpurbo at 00:15, 8 May 2019

2019-05-08T00:15:21Z

@@ Line 2: / Line 2: @@
 The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or board). The SDR module provides signal processing and digital data transfer between the RF signals and the host. The RF module provides the wireless transmission of the data. The SDR and RF module boards are each on a 5.5" x 3.25" PCB outline. This is a stacked design with a single interface connector between them. The RF module uses the same PCB layout with different component stuffing options and is capable of supporting the following frequency bands: 850, 900, 1800, 1900 MHz. The SDR1 is based in large part on the USRP1 design.
 The design resources provided are as follows:
@@ Line 14: / Line 17: @@
          BOM in text format: Low band and High band
          Gerber files with assembly and fabrication drawings

Onnowpurbo: New page: Range Networks SDR1 Open Source Software-Defined Radio The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or boa...

2015-02-26T11:52:22Z

New page: Range Networks SDR1 Open Source Software-Defined Radio The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or boa...

New page

Range Networks SDR1 Open Source Software-Defined Radio

The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or board). The SDR module provides signal processing and digital data transfer between the RF signals and the host. The RF module provides the wireless transmission of the data. The SDR and RF module boards are each on a 5.5" x 3.25" PCB outline. This is a stacked design with a single interface connector between them. The RF module uses the same PCB layout with different component stuffing options and is capable of supporting the following frequency bands: 850, 900, 1800, 1900 MHz. The SDR1 is based in large part on the USRP1 design.

The design resources provided are as follows:

Software-defined radio (SDR) module
Schematics in pdf format
BOM in text format
Gerber files with assembly and fabrication drawings
NVM file for Silicon Labs Si5332C OTP eeprom
RF module
Schematics in pdf format
BOM in text format: Low band and High band
Gerber files with assembly and fabrication drawings

==Referensi==

* https://github.com/RangeNetworks/hardware-designs