Onnowpurbo: /* Pranala Menarik */

2012-04-08T22:45:17Z

Pranala Menarik

@@ Line 107: / Line 107: @@
 ==Pranala Menarik==
 * [[rtorrent]]
 * [[rtorrent.rc]]

Onnowpurbo: /* Pranala Menarik */

2012-04-07T00:53:00Z

Pranala Menarik

← Older revision		Revision as of 00:53, 7 April 2012
Line 109:		Line 109:
	* [[rtorrent]]		* [[rtorrent]]
	* [[rtorrent.rc]]		* [[rtorrent.rc]]
			* [[rtorrent: modifikasi untuk mendukung magnet]]
			* [[rtorrent: cara penggunaan]]
			* [[rtorrent: menjalankan di background]]
	* [[Bittorrent]]		* [[Bittorrent]]

Onnowpurbo at 22:06, 6 April 2012

2012-04-06T22:06:52Z

@@ Line 1: / Line 1: @@
   # This is an example resource file for rTorrent. Copy to
   # ~/.rtorrent.rc and enable/modify the options as needed. Remember to
@@ Line 101: / Line 103: @@
   # decent hash checking rate.
   #hash_max_tries = 10

Onnowpurbo: New page: # This is an example resource file for rTorrent. Copy to # ~/.rtorrent.rc and enable/modify the options as needed. Remember to # uncomment the options you wish to enable. # Maximum a...

2012-04-06T22:06:06Z

New page: # This is an example resource file for rTorrent. Copy to # ~/.rtorrent.rc and enable/modify the options as needed. Remember to # uncomment the options you wish to enable. # Maximum a...

New page

# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.

# Maximum and minimum number of peers to connect to per torrent.
#min_peers = 40
#max_peers = 100

# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 50

# Maximum number of simultanious uploads per torrent.
#max_uploads = 15

# Global upload and download rate in KiB. "0" for unlimited.
#download_rate = 0
#upload_rate = 0

# Default directory to save the downloaded torrents.
#directory = ./

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
#session = ./session

# Watch a directory for new torrents, and stop those that have been
# deleted.
#schedule = watch_directory,5,5,load_start=./watch/*.torrent
#schedule = untied_directory,5,5,stop_untied=

# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M

# The ip address reported to the tracker.
#ip = 127.0.0.1
#ip = rakshasa.no

# The ip address the listening socket and outgoing connections is
# bound to.
#bind = 127.0.0.1
#bind = rakshasa.no

# Port range to use for listening.
#port_range = 6890-6999

# Start opening ports at a random position within the port range.
#port_random = no

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
#check_hash = no

# Set whetever the client should try to connect to UDP trackers.
#use_udp_trackers = yes

# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext

# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
# dht = auto

# UDP port to use for DHT.
#
# dht_port = 6881

# Enable peer exchange (for torrents not marked private)
#
# peer_exchange = yes

#
# Do not modify the following parameters unless you know what you're doing.
#

# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10

# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10

Rtorrent.rc - Revision history

Onnowpurbo: /* Pranala Menarik */

Onnowpurbo: /* Pranala Menarik */

Onnowpurbo at 22:06, 6 April 2012

Onnowpurbo: New page: # This is an example resource file for rTorrent. Copy to # ~/.rtorrent.rc and enable/modify the options as needed. Remember to # uncomment the options you wish to enable. # Maximum a...