UBNT: openwrt: Difference between revisions

From OnnoCenterWiki
Jump to navigationJump to search
← Older edit
Onnowpurbo (talk | contribs)
69,477 edits
Onnowpurbo (talk | contribs)
69,477 edits
No edit summary
Onnowpurbo (talk | contribs)
69,477 edits
 
(11 intermediate revisions by the same user not shown)
Line 6: Line 6:
WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware”
WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware”


==Download OpenWRT==


Download OpenWRT firmware untuk Ubiquiti dari
Download OpenWRT firmware untuk Ubiquiti dari


http://downloads.openwrt.org/snapshots/trunk/atheros/
Nano2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-squashfs.bin
Pico2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin
Nano5 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt5-squashfs.bin


Alternatif lain menggunakan Kamikaze OpenWRT (terakhir di developed 2009)


Nano2 http://kamikaze.openwrt.org/8.09.2/atheros/openwrt-atheros-ubnt2-squashfs.bin
Pico2 http://kamikaze.openwrt.org/8.09.2/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin
Nano5 http://kamikaze.openwrt.org/8.09.2/atheros/openwrt-atheros-ubnt5-squashfs.bin


Requirements
==Flash Update==


    - A computer running Microsoft Windows (Windows XP, Vista or 7)
* Set IP PC 192.168.1.x
    - Direct Ethernet cable connection between PC and Bullet, Pico or Nano/Loco.
* Matikan Device UBNT
    - Network settings of PC: IP address: 192.168.1.254 and net mask: 255.255.255.0
* Tekan tombol Reset
    - TFTP client on PC (TFTPD32 is recommended)  
* Nyalakan Device UBNT
    - OpenWRT firmware file. You can download it from here:
* Lepaskan tombol Reset setelah ~10 detik (tidak lebih) sesudah device UBNT di nyalakan. Kita akan mengetahui-nya karena LED akan berubah.
    For Nano2 or Bullet2 devices: http://kamikaze.openwrt.org/8.09.1/atheros/openwrt-atheros-ubnt2-squashfs.bin
* Ping 192.168.1.20. Jika ada responds, kita siap untuk meng-upload image. Jika tidak maka mulai lagi dari awal.
    For Nano5 or Bullet5 devices: http://kamikaze.openwrt.org/8.09.1/atheros/openwrt-atheros-ubnt5-squashfs.bin
* tftp image menggunakan mode binary ke 192.168.1.20 sebagai 'flash_update'.
    For Pico2 devices: http://kamikaze.openwrt.org/8.09.1/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin


Steps
tftp 192.168.1.20
tftp> binary
tftp> trace
tftp> put openwrt-atheros-ubnt2-squashfs.bin flash_update


    - First of all, disconnect the Ethernet cable from Pico, Bullet2 or Nano/Loco2.
==Akses ke UBNT OpenWRT==
    - Connect the Ethernet Cable and immediately press the Reset button (near the device’s RJ45 connector) for 10 seconds.
    - Make sure that device responds to pinging (command: ping 192.168.1.20, by default). If not, please repeat previous steps.
    - Using the TFTP client, upload the firmware file (extension .bin) to the Bullet2 or Nano/Loco2 IP address (192.168.1.20, by default). If the device doesn’t accept the firmware filename, rename it to “flash_update”.
    - Signal LEDs will be blinking during firmware upgrade.
    - Wait for about 7 minutes (Warning: Do not disconnect the Ethernet cable during procedure).


Configuring IP addressl
Lakukan


Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account.
telnet 192.168.1.1


Recovery procedure
Akan tampak
Recovery Ubiquiti Firmwarel


     Ubiquiti AirOS firmware can be downloaded from http://www.ubnt.com/support/airos.php
Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
  === IMPORTANT ============================
  Use 'passwd' to set your login password
  this will disable telnet and enable SSH
  ------------------------------------------
 
BusyBox v1.19.4 (2012-07-19 03:29:28 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
  _______                    ________        __
  |      |.-----.-----.-----.|  |  |  |.----.|  |_
  |  -  ||  _  |  -__|     ||  |  |  ||  _||  _|
  |_______||  __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S  F R E E D O M
  -----------------------------------------------------
  ATTITUDE ADJUSTMENT (Bleeding Edge, r32777)
  -----------------------------------------------------
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
  -----------------------------------------------------


Set Password Root


    - First of all, disconnect the Ethernet cable from the device.
passwd passwordrootyangkitainginkan
    - Connect the Ethernet Cable and immediately press the Reset button (near the device’s RJ45 connector) for 10 seconds.
    - Make sure that Bullet2 or Nano/Loco2 responds to pinging (command: ping 192.168.1.20, by default). If not, please repeat previous steps.
    - Using the TFTP client, upload the firmware file (extension .bin) to the device IP address (192.168.1.20, by default). If it doesn’t accept the firmware filename, rename it to “flash_update”.
    - Signal LEDs will be blinking during firmware upgrade.
    - Wait for about 7 minutes (Warning: Do not disconnect the Ethernet cable during procedure).
    - Now the device should be alive and with the AirOS firmware loaded.


===Akses SSH===
Selanjutnya akses menggunakan ssh
ssh root@192.168.1.1
==Prosedur Recovery Firmware==
* [[UBNT: Rebuild Firmware | Kita dapat merecover AirOS firmware melalui prosedur recovery firmware]]


==Referensi==
==Referensi==
Line 56: Line 93:
* http://wiki.openwrt.org/toh/ubiquiti/nanostation
* http://wiki.openwrt.org/toh/ubiquiti/nanostation
* http://downloads.openwrt.org/snapshots/trunk/atheros/
* http://downloads.openwrt.org/snapshots/trunk/atheros/
* http://wiki.openwrt.org/toh/start#ubiquiti


==Pranala Menarik==
==Pranala Menarik==
Line 61: Line 99:
* [[UBNT]]
* [[UBNT]]
* [[UBNT: Teknik Recovery]]
* [[UBNT: Teknik Recovery]]
* [[UBNT: Upload Firmware]]
* [[UBNT: Rebuild Firmware]]
* [[UBNT: Rebuild Firmware]]
* [[UBNT: firmware dengan OLSR]]
* [[UBNT: openwrt]]
* [[UBNT: openwrt]]
* [[UBNT: olsr dengan openwrt]]
* [[UBNT: olsr dengan openwrt]]
* [[UBNT: olsr dengan kamikaze openwrt]]
* [[UBNT: olsr dengan backfire openwrt]] '''RECOMMENDED'''
* [[UBNT: UniFi]]
* [[UBNT: UniFi Konfigurasi Awal]]
* [[UBNT: UniFi Manajemen HotSpot]]
* [[UBNT: OLSR Pembuatan Firmware]]
* [[UBNT: OLSR Konfigurasi]]
* [[OLSR - di UBNT]]
* [[OLSR - di UBNT]]
* [[OLSR - di Ubuntu]]
* [[OpenWRT]]

Latest revision as of 06:06, 22 July 2012

Sumber: http://wiki.ubnt.com/Installing_OpenWRT_on_NanoStations/Bullets

Berikut adalah prosedur untuk mem-flash Ubiquiti Bullet 2 atau Nano2/Loco2. Prosedur ini akan mengganti AirOS firmware dengan OpenWRT firmware.

WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware”

Download OpenWRT

Download OpenWRT firmware untuk Ubiquiti dari 

http://downloads.openwrt.org/snapshots/trunk/atheros/
Nano2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-squashfs.bin
Pico2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin
Nano5 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt5-squashfs.bin

Alternatif lain menggunakan Kamikaze OpenWRT (terakhir di developed 2009) 

Nano2 http://kamikaze.openwrt.org/8.09.2/atheros/openwrt-atheros-ubnt2-squashfs.bin
Pico2 http://kamikaze.openwrt.org/8.09.2/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin
Nano5 http://kamikaze.openwrt.org/8.09.2/atheros/openwrt-atheros-ubnt5-squashfs.bin

Flash Update

  • Set IP PC 192.168.1.x
  • Matikan Device UBNT
  • Tekan tombol Reset
  • Nyalakan Device UBNT
  • Lepaskan tombol Reset setelah ~10 detik (tidak lebih) sesudah device UBNT di nyalakan. Kita akan mengetahui-nya karena LED akan berubah.
  • Ping 192.168.1.20. Jika ada responds, kita siap untuk meng-upload image. Jika tidak maka mulai lagi dari awal.
  • tftp image menggunakan mode binary ke 192.168.1.20 sebagai 'flash_update'.
tftp 192.168.1.20
tftp> binary
tftp> trace
tftp> put openwrt-atheros-ubnt2-squashfs.bin flash_update

Akses ke UBNT OpenWRT

Lakukan 

telnet 192.168.1.1

Akan tampak 

Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
 === IMPORTANT ============================
  Use 'passwd' to set your login password
  this will disable telnet and enable SSH
 ------------------------------------------
 

BusyBox v1.19.4 (2012-07-19 03:29:28 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 ATTITUDE ADJUSTMENT (Bleeding Edge, r32777)
 -----------------------------------------------------
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
 -----------------------------------------------------

Set Password Root 

passwd passwordrootyangkitainginkan


Akses SSH

Selanjutnya akses menggunakan ssh 

ssh root@192.168.1.1

Prosedur Recovery Firmware

Referensi

Pranala Menarik

Retrieved from "https://lms.onnocenter.or.id/wiki/index.php?title=UBNT:_openwrt&oldid=33241"