OLSR - di Ubuntu: Difference between revisions

From OnnoCenterWiki
Jump to navigationJump to search
← Older edit
Onnowpurbo (talk | contribs)
69,477 edits
Onnowpurbo (talk | contribs)
69,477 edits
No edit summary
Onnowpurbo (talk | contribs)
69,477 edits
 
(47 intermediate revisions by the same user not shown)
Line 1: Line 1:
Sumber: http://wmunguiam.blogspot.com/2009/01/olsr-over-ubuntu-804.html
Sumber: http://wmunguiam.blogspot.com/2009/01/olsr-over-ubuntu-804.html


Pada dasarnya ada dua (2) cara utk mengaktifkan OLSR di Ubuntu
Pada dasarnya ada dua (2) cara utk mengaktifkan [[OLSR]] di [[Ubuntu]], yaitu


* Install dari repository
* Install dari repository
* Compile dari source code
* Compile dari [[source code]]


==Instalasi OLSRD dari repository==
==Instalasi OLSRD dari repository==


OLSR dapat di instalasi langsung menggunakan perintah
[[OLSR]] dapat di instalasi langsung dari [[repository]] menggunakan perintah


  sudo apt-get install olsrd olsrd-plugins
  sudo apt-get install olsrd olsrd-plugins
hanya saja ini biasanya bukan versi bleeding edge :)
tapi lumayan stabil lah untuk ngoprek.
Masalah dengan olsrd hasil apt-get adalah
* olsrd dengan /etc/init.d/olsrd mencari /etc/olsrd.conf bukan /etc/olsrd/olsrd.conf. Akibatnya akan abort karena tidak menemukan file konfigurasi.
* olsrd akan melaporan error, buang LinkQualityDijkstraLimit dan LinkQualityWinSize di olsrd.conf. Caranya edit
vi /etc/olsrd.conf
Remark line 124
# LinkQualityDijkstraLimit 3 3.0
Remark line 240
# LinkQualityWinSize    100


==Compile dari Source Code==
==Compile dari Source Code==
Line 21: Line 39:
Download [[source code]] dari
Download [[source code]] dari


1.- Get information
http://www.olsr.org/mediawiki/index.php/Releases
http://www.olsr.org/?q=download
 
Copy, Extract dan Compile
 
wget http://www.olsr.org/releases/0.9/olsrd-0.9.0.2.tar.bz2
cp olsrd-0.9.0.2.tar.bz2 /usr/local/src/
cd /usr/local/src
tar jxvf olsrd-0.9.0.2.tar.bz2
cd /usr/local/src/olsrd-0.9.0.2
make all
make install
make libs
make install_libs
mkdir -p /etc
cp -i files/olsrd.conf.default.lq /etc/olsrd.conf


2.- Get OLSR package
Sedikit catatan tentang olsrd
Visit: http://packages.ubuntu.com/search?keywords=olsrd


========= C O N F I G U R A T I O N - F I L E ============
olsrd uses the configfile /etc/olsrd.conf
a default configfile. A sample RFC-compliance aimed
configfile can be found in olsrd.conf.default.rfc.
However none of the larger OLSRD using networks use that
so install a configfile with activated link quality exstensions
per default.
can be found at files/olsrd.conf.default.lq
==========================================================
mkdir -p /etc
cp -i files/olsrd.conf.default.lq /etc/olsrd.conf
-------------------------------------------
Edit /etc/olsrd.conf before running olsrd!!
-


If you download lastest olsr package, install it by going to olsrd dowloaded directory, uncompress it and:
==Edit OLSRD.CONF==
wmunguiam@server:~$ make
wmunguiam@server:~$ sudo make install


4.-Edit /etc/olsrd/olsrd.conf as below as example (Modify if you need)
Edit olsrd.conf
wmunguiam@server:~$ sudo cp /etc/olsrd/olsrd.conf /etc/olsrd/olsrd.conf.original
wmunguiam@server:~$ sudo vim /etc/olsrd/olsrd.conf


    DebugLevel 1
sudo cp /etc/olsrd.conf /etc/olsrd.conf.original
    Interface "wlan1"
sudo vi /etc/olsrd.conf
    {
 
Pastikan ada interface yang aktif menggunakan OLSR, misalnya eth1, wlan0 dll.
Contoh konfigurasi sederhana
 
InterfaceDefaults {
    Ip4Broadcast      255.255.255.255
}
Interface "eth1" {
     # Ip4Broadcast 255.255.255.255
     # Ip4Broadcast 255.255.255.255
     # Ip6AddrType site-local
     # Ip6AddrType site-local
     # Ip6MulticastSite ff05::11
     # Ip6MulticastSite ff05::11
     # Ip6MulticastGlobal ff0e::1
     # Ip6MulticastGlobal ff0e::1
 
     HelloInterval 6.0
     HelloInterval 6.0
     HelloValidityTime 600.0
     HelloValidityTime 600.0
Line 54: Line 101:
     # Weight 0
     # Weight 0
     # LinkQualityMult 192.168.0.1 0.5
     # LinkQualityMult 192.168.0.1 0.5
    }
Tambahkan untuk Plugin txtinfo


    }
LoadPlugin "olsrd_txtinfo.so.0.1"
    LinkQualityFishEye 1
    LinkQualityDijkstraLimit 3 3.0
    IpVersion 4
    ClearScreen yes
    Hna4
     {
     {
     # Internet gateway:
     PlParam "port" "8080"
    # Agregado WALTER
     PlParam "Host" "127.0.0.1"
     # 10.10.10.0 255.255.255.0
     # PlParam "Net" "0.0.0.0 0.0.0.0"
     # 0.0.0.0 0.0.0.0
     # PlParam "Host" "80.23.53.22"
     # more entries can be added:
     # # PlParam "Net" "192.168.0.0 255.255.0.0" 
     # 192.168.1.0 255.255.255.0
     }
     }
    Hna6
    {
    # Internet gateway:
    # :: 0
    # more entries can be added:
    # fec0:2200:106:: 48
    }
    AllowNoInt no
    #TosValue 16
    Willingness 7
    IpcConnect
    {
    MaxConnections 1
    Host 127.0.0.1
    Host 10.10.10.11
    Net 10.10.10.0 255.255.255.0
    }
    UseHysteresis no
    #HystScaling 0.50
    #HystThrHigh 0.80
    #HystThrLow 0.30
    LinkQualityLevel 2
    LinkQualityWinSize 100
    Pollrate 0.1
    TcRedundancy 2
    MprCoverage 5
    #LoadPlugin "olsrd_httpinfo.so.0.1"
    #{
    # # defaults to 1978
    # PlParam "Port" "8080"
    # #PlParam "Host" "80.23.53.22"
    # #PlParam "Net" "10.0.0.0 255.0.0.0"
    # #PlParam "Net" "0.0.0.0 0.0.0.0"
    #}
    #LoadPlugin "olsrd_dyn_gw.so.0.4"
    #{
    # PlParam "Interval" "40"
    # PlParam "Ping" "141.1.1.1"
    # PlParam "Ping" "194.25.2.129"
    #}
    #LoadPlugin "olsrd_nameservice.so.0.2"
    #{
    #PlParam "name" "xxx"
    #PlParam "a.b.c.d" "xxx-eth"
    #PlParam "a.b.c.e" "xxx-bbb"
    #PlParam "a.b.c.f" "xxx-olsr"
    #PlParam "suffix" ".olsr"
    #}


    #LoadPlugin "olsrd_dot_draw.so.0.3"
    #{
    #PlParam "accept" "192.168.0.5"
    #PlParam "port" "2004"
    #}


5.-Edit linux network interface(s) to work as Ad-hoc node
Kadang kala pada saat kita jalankan olsrd akan melaporan error, buang LinkQualityDijkstraLimit dan LinkQualityWinSize di olsrd.conf. Caranya edit
wmunguiam@server:~$ sudo vim /etc/network/interfaces
 
vi /etc/olsrd.conf
 
Remark line 124
 
# LinkQualityDijkstraLimit 3 3.0
 
Remark line 240
 
# LinkQualityWinSize    100
 
==Cek konfigurasi==
 
Sebaiknya cek konfigurasi menggunakan perintah
 
sudo olsrd -d 2
 
atau bagi yang menginstall menggunakan apt-get bisa
 
sudo olsrd -d 2 -f /etc/olsrd/olsrd.conf
 
Kayanya menggunakan apt-get ada beberapa error, di beri # aja di line yang error. Biasanya setelah di # error yang ada maka olsrd akan jalan.
 
===IPv6===
 
Menjalankan OLSR Untuk IPv6
 
sudo olsrd -d 2 -ipv6
 
==Edit Interface==
 
Kita dapat melakukannya menggunakan
 
* iwconfig di console
* edit /etc/network/interface
 
Dengan asumsi eth1 adalah interface [[wireless]].
Edit di console
 
iwconfig wlan0 mode ad-hoc
iwconfig wlan0 essid MESH
iwconfig wlan0 ap 02:ca:ff:ee:ba:be
iwconfig wlan0 channel 1
ifconfig wlan0 10.1.1.1
ifconfig wlan0 netmask 255.0.0.0
 
atau
 
iwconfig wlan0 mode ad-hoc essid MESH ap 02:ca:ff:ee:ba:be channel 1
ifconfig wlan0 10.1.1.1 netmask 255.0.0.0
 
 
Edit
 
vi /etc/network/interfaces
 
Isi kira-kira sebagi berikut


     auto lo
     auto lo
     iface lo inet loopback
     iface lo inet loopback
 
    auto wlan0
    allow-hot plug wlan0
    iface wlan0 inet static
    address 10.1.1.1
    broadcast 10.255.255.255
    netmask 255.0.0.0
    wireless-mode ad-hoc
    wireless-channel 1
    wireless-essid MESH
    wireless-bssid 02:ca:ff:ee:ba:be
     auto wlan0
     auto wlan0
     allow-hot plug wlan0
     allow-hot plug wlan0
Line 135: Line 194:
     address 10.10.10.11
     address 10.10.10.11
     netmask 255.255.255.0
     netmask 255.255.255.0
    wireless-mode ad-hoc
    wireless-channel 11
    wireless-key s:12345
    wireless-essid mesh
    #auto eth0
    #iface eth0 inet dhcp
   
    # Konfigurasi IPv6
    iface wlan0 inet6 static
    address 2001:123:127::127
    netmask 128
     wireless-mode ad-hoc
     wireless-mode ad-hoc
     wireless-channel 1
     wireless-channel 1
    wireless-key s:12345
     wireless-essid MESH
     wireless-essid MESH
    wireless-bssid 02:ca:ff:ee:ba:be
==Restart Networking==
networking and OLSR
sudo /etc/init.d/networking restart
sudo /etc/init.d/olsrd start
Jika pada saat melakukan


    #auto eth0
sudo /etc/init.d/network restart
    #iface eth0 inet dhcp
 
Keluar error berikut
 
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Device or resource busy.
 
Kemungkinan wireless interface / hardware yang anda gunakan tidak mendukung mode ad-hoc. Kita perlu menggunakan USB wireless card lain.


6.-Restart services: networking and OLSR
==Verifikasi Jaringan==
wmunguiam@server:~$ sudo /etc/init.d/network restart
wmunguiam@server:~$ sudo /etc/init.d/olsrd start


OBS: If you get this:
Asumsinya eth1 adalah interface [[WLAN]].
wmunguiam@server:~$ sudo /etc/init.d/network restart


    Error for wireless request "Set Mode" (8B06) :
ifconfig eth1
    SET failed on device wlan0 ; Invalid argument.
    Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Device or resource busy.


Means your wireless Interface (Hardware) does not support working on Ad-hoc mode. You have to use (recommended) an USB Wireless Card.
eth1      Link encap:Ethernet  HWaddr 00:21:00:50:a3:90 
          inet addr:172.16.1.2  Bcast:172.16.255.255  Mask:255.255.0.0
          inet6 addr: fe80::221:ff:fe50:a390/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:52 errors:0 dropped:0 overruns:0 frame:188
          TX packets:88 errors:11 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:3356 (3.3 KB) TX bytes:14387 (14.3 KB)
          Interrupt:17


Cek wireless


7.-Verify services
iwconfig eth1
wmunguiam@server:~$ ifconfig wlan1
wlan1 Link encap:Ethernet direcciónHW 00:e0:4c:00:39:1d
inet dirección:10.10.10.11 Difusión:10.10.10.255 Máscara:255.255.255.0
dirección inet6: fe80::2e0:4cff:fe00:391d/64 Alcance:Vínculo
ARRIBA DIFUSIÓN CORRIENDO MULTICAST MTU:1500 Métrica:1
RX packets:0 errors:17 dropped:0 overruns:0 frame:0
TX packets:181 errors:0 dropped:0 overruns:0 carrier:0
colisiones:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:10918 (10.6 KB)


wmunguiam@server:~$ iwconfig
eth1      IEEE 802.11bg  ESSID:"MESH"
wlan1 802.11b/g linked ESSID:"MESH"
          Mode:Ad-Hoc Frequency:2.412 GHz  Cell: 02:CA:FF:EE:BA:BE 
Mode:Ad-Hoc Channel=1 Cell: B2:EF:82:A6:57:82
          Bit Rate=54 Mb/s   Tx-Power:24 dBm 
Bit Rate=54 Mb/s
          Retry min limit:7  RTS thr:off  Fragment thr:off
Retry:on Fragment thr:off
          Power Management:off
Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm
          Link Quality=5/5  Signal level=-21 dBm Noise level=-57 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
          Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
          Tx excessive retries:0 Invalid misc:0   Missed beacon:0  


wmunguiam@server:~$ route
Cek Routing
Tabla de rutas IP del núcleo
Destino Pasarela Genmask Indic Métric Ref Uso Interfaz
192.168.1.0 * 255.255.255.0 U 0 0 0 wlan0
10.10.10.0 * 255.255.255.0 U 0 0 0 wlan1
link-local * 255.255.0.0 U 1000 0 0 wlan1
default 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0


OBS: WLAN0 interface to connect to internet (GW)
netstat -nr


Kernel IP routing table
Destination    Gateway        Genmask        Flags  MSS Window  irtt Iface
0.0.0.0        172.16.1.1      0.0.0.0        UG        0 0          0 eth1
172.16.0.0      0.0.0.0        255.255.0.0    U        0 0          0 eth1
172.16.1.1      172.16.1.1      255.255.255.255 UGH      0 0          0 eth1
172.16.1.2      172.16.1.2      255.255.255.255 UGH      0 0          0 eth1


Perhatikan host dengan netmask 255.255.255.255, ini merupakan host yang di tambahkan secara automatis oleh [[OLSR]].


==Referensi==
==Referensi==
Line 196: Line 280:
==Pranala Menarik==
==Pranala Menarik==


* [[WiFi: HotSpot - Linksys WRT54GL]]
* [[WiFi: HotSpot - Linksys WRT54GL Konfigurasi Orginal]]
* [[WiFi: HotSpot - Linksys WRT54GL Upgrade dd-wrt]]
* [[WiFi: HotSpot - Linksys WRT54GL Upgrade dd-wrt]]
* [[WiFi: HotSpot - Linksys WRT54GL Upgrade dd-wrt OLSR]]
* [[WiFi: HotSpot - Linksys WRT54GL Upgrade dd-wrt OLSR]]
* [[WiFi: HotSpot - DD-WRT WRT54GL Mengaktifkan OLSR]]
* [[WiFi: HotSpot - DD-WRT WRT54GL Mengaktifkan OLSR]]
* [[WiFi: HotSpot - Linksys WRT54GL Upgrade FreiFunk Firmware]]
* [[WiFi: HotSpot - Linksys WRT54GL Konfigurasi FreiFunk]]
* [[WiFi: HotSpot - Linksys WRT54GL FreiFunk Setelah Upgrade Software]]
* [[WiFi: HotSpot - Linksys WRT54GL FreiFunk Peta Mesh Network]]
* [[De-Bricking WRT54GL v.1.1]]
* [[OLSR]]
* [[OLSR]]
* [[OLSR - di Ubuntu]]
* [[WNDW: Jaringan Mesh dengan OLSR]]
* [[WNDW: Jaringan Mesh dengan OLSR]]
* [[OLSR - di Ubuntu]]
* [[WiFi: HotSpot]]
* [[Wireless Internet Berbasis WiFi]]
 
[[Category: WiFi]]
[[Category: HotSpot]]

Latest revision as of 03:34, 9 August 2015

Sumber: http://wmunguiam.blogspot.com/2009/01/olsr-over-ubuntu-804.html

Pada dasarnya ada dua (2) cara utk mengaktifkan OLSR di Ubuntu, yaitu

Instalasi OLSRD dari repository

OLSR dapat di instalasi langsung dari repository menggunakan perintah 

sudo apt-get install olsrd olsrd-plugins

hanya saja ini biasanya bukan versi bleeding edge :) tapi lumayan stabil lah untuk ngoprek.

Masalah dengan olsrd hasil apt-get adalah

  • olsrd dengan /etc/init.d/olsrd mencari /etc/olsrd.conf bukan /etc/olsrd/olsrd.conf. Akibatnya akan abort karena tidak menemukan file konfigurasi.
  • olsrd akan melaporan error, buang LinkQualityDijkstraLimit dan LinkQualityWinSize di olsrd.conf. Caranya edit
vi /etc/olsrd.conf

Remark line 124 

# LinkQualityDijkstraLimit 3 3.0

Remark line 240 

# LinkQualityWinSize    100

Compile dari Source Code

Siapkan aplikasi pendukung 

sudo apt-get install kernel-package libncurses5-dev fakeroot wget \
bzip2 g++ libssl-dev libxml2-dev doxygen bison flex libc6

Download source code dari 

http://www.olsr.org/mediawiki/index.php/Releases

Copy, Extract dan Compile 

wget http://www.olsr.org/releases/0.9/olsrd-0.9.0.2.tar.bz2
cp olsrd-0.9.0.2.tar.bz2 /usr/local/src/
cd /usr/local/src
tar jxvf olsrd-0.9.0.2.tar.bz2 
cd /usr/local/src/olsrd-0.9.0.2
make all
make install
make libs
make install_libs
mkdir -p /etc
cp -i files/olsrd.conf.default.lq /etc/olsrd.conf

Sedikit catatan tentang olsrd 

========= C O N F I G U R A T I O N - F I L E ============
olsrd uses the configfile /etc/olsrd.conf
a default configfile. A sample RFC-compliance aimed
configfile can be found in olsrd.conf.default.rfc.
However none of the larger OLSRD using networks use that
so install a configfile with activated link quality exstensions
per default.
can be found at files/olsrd.conf.default.lq
==========================================================
mkdir -p /etc
cp -i files/olsrd.conf.default.lq /etc/olsrd.conf
-------------------------------------------
Edit /etc/olsrd.conf before running olsrd!!
-

Edit OLSRD.CONF

Edit olsrd.conf 

sudo cp /etc/olsrd.conf /etc/olsrd.conf.original
sudo vi /etc/olsrd.conf

Pastikan ada interface yang aktif menggunakan OLSR, misalnya eth1, wlan0 dll. Contoh konfigurasi sederhana 

InterfaceDefaults {
    Ip4Broadcast      255.255.255.255
}
Interface "eth1" {
   # Ip4Broadcast 255.255.255.255
   # Ip6AddrType site-local
   # Ip6MulticastSite ff05::11
   # Ip6MulticastGlobal ff0e::1

   HelloInterval 6.0
   HelloValidityTime 600.0
   TcInterval 0.5
   TcValidityTime 300.0
   MidInterval 10.0
   MidValidityTime 300.0
   HnaInterval 10.0
   HnaValidityTime 300.0
   # Weight 0
   # LinkQualityMult 192.168.0.1 0.5
   }


Tambahkan untuk Plugin txtinfo 

LoadPlugin "olsrd_txtinfo.so.0.1"
   {
   PlParam "port" "8080"
   PlParam "Host" "127.0.0.1"
   # PlParam "Net" "0.0.0.0 0.0.0.0"
   # PlParam "Host" "80.23.53.22"
   # # PlParam "Net" "192.168.0.0 255.255.0.0"  
   }


Kadang kala pada saat kita jalankan olsrd akan melaporan error, buang LinkQualityDijkstraLimit dan LinkQualityWinSize di olsrd.conf. Caranya edit 

vi /etc/olsrd.conf

Remark line 124 

# LinkQualityDijkstraLimit 3 3.0

Remark line 240 

# LinkQualityWinSize    100

Cek konfigurasi

Sebaiknya cek konfigurasi menggunakan perintah 

sudo olsrd -d 2

atau bagi yang menginstall menggunakan apt-get bisa 

sudo olsrd -d 2 -f /etc/olsrd/olsrd.conf

Kayanya menggunakan apt-get ada beberapa error, di beri # aja di line yang error. Biasanya setelah di # error yang ada maka olsrd akan jalan.

IPv6

Menjalankan OLSR Untuk IPv6 

sudo olsrd -d 2 -ipv6

Edit Interface

Kita dapat melakukannya menggunakan

  • iwconfig di console
  • edit /etc/network/interface

Dengan asumsi eth1 adalah interface wireless. Edit di console 

iwconfig wlan0 mode ad-hoc
iwconfig wlan0 essid MESH
iwconfig wlan0 ap 02:ca:ff:ee:ba:be
iwconfig wlan0 channel 1
ifconfig wlan0 10.1.1.1
ifconfig wlan0 netmask 255.0.0.0

atau 

iwconfig wlan0 mode ad-hoc essid MESH ap 02:ca:ff:ee:ba:be channel 1
ifconfig wlan0 10.1.1.1 netmask 255.0.0.0


Edit 

vi /etc/network/interfaces

Isi kira-kira sebagi berikut 

   auto lo
   iface lo inet loopback

   auto wlan0
   allow-hot plug wlan0
   iface wlan0 inet static
   address 10.1.1.1
   broadcast 10.255.255.255
   netmask 255.0.0.0
   wireless-mode ad-hoc
   wireless-channel 1
   wireless-essid MESH
   wireless-bssid 02:ca:ff:ee:ba:be

   auto wlan0
   allow-hot plug wlan0
   iface wlan0 inet static
   address 10.10.10.11
   netmask 255.255.255.0
   wireless-mode ad-hoc
   wireless-channel 11
   wireless-key s:12345
   wireless-essid mesh

   #auto eth0
   #iface eth0 inet dhcp
   
   # Konfigurasi IPv6
   iface wlan0 inet6 static
   address 2001:123:127::127
   netmask 128
   wireless-mode ad-hoc
   wireless-channel 1
   wireless-essid MESH
   wireless-bssid 02:ca:ff:ee:ba:be

Restart Networking

networking and OLSR 

sudo /etc/init.d/networking restart
sudo /etc/init.d/olsrd start


Jika pada saat melakukan 

sudo /etc/init.d/network restart

Keluar error berikut 

Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Device or resource busy.

Kemungkinan wireless interface / hardware yang anda gunakan tidak mendukung mode ad-hoc. Kita perlu menggunakan USB wireless card lain.

Verifikasi Jaringan

Asumsinya eth1 adalah interface WLAN. 

ifconfig eth1

eth1      Link encap:Ethernet  HWaddr 00:21:00:50:a3:90  
          inet addr:172.16.1.2  Bcast:172.16.255.255  Mask:255.255.0.0
          inet6 addr: fe80::221:ff:fe50:a390/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:52 errors:0 dropped:0 overruns:0 frame:188
          TX packets:88 errors:11 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:3356 (3.3 KB)  TX bytes:14387 (14.3 KB)
          Interrupt:17

Cek wireless 

iwconfig eth1

eth1      IEEE 802.11bg  ESSID:"MESH"  
          Mode:Ad-Hoc  Frequency:2.412 GHz  Cell: 02:CA:FF:EE:BA:BE   
          Bit Rate=54 Mb/s   Tx-Power:24 dBm   
          Retry min limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality=5/5  Signal level=-21 dBm  Noise level=-57 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Cek Routing 

netstat -nr

Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
0.0.0.0         172.16.1.1      0.0.0.0         UG        0 0          0 eth1
172.16.0.0      0.0.0.0         255.255.0.0     U         0 0          0 eth1
172.16.1.1      172.16.1.1      255.255.255.255 UGH       0 0          0 eth1
172.16.1.2      172.16.1.2      255.255.255.255 UGH       0 0          0 eth1

Perhatikan host dengan netmask 255.255.255.255, ini merupakan host yang di tambahkan secara automatis oleh OLSR.

Referensi

Pranala Menarik

Retrieved from "https://lms.onnocenter.or.id/wiki/index.php?title=OLSR_-_di_Ubuntu&oldid=44268"