UBNT: openwrt: Difference between revisions

From OnnoCenterWiki
Jump to navigationJump to search
← Older editNewer edit →
Onnowpurbo (talk | contribs)
69,477 edits
Onnowpurbo (talk | contribs)
69,477 edits
Onnowpurbo (talk | contribs)
69,477 edits
Line 17: Line 17:
==Flash Update==
==Flash Update==


Steps


    - First of all, disconnect the Ethernet cable from Pico, Bullet2 or Nano/Loco2.  
 
    - Connect the Ethernet Cable and immediately press the Reset button (near the device’s RJ45 connector) for 10 seconds.  
* Set IP PC 192.168.1.x
    - Make sure that device responds to pinging (command: ping 192.168.1.20, by default). If not, please repeat previous steps.
* Matikan Device UBNT
    - Using the TFTP client, upload the firmware file (extension .bin) to the Bullet2 or Nano/Loco2 IP address (192.168.1.20, by default). If the device doesn’t accept the firmware filename, rename it to “flash_update”.  
* Tekan tombol Reset
    - Signal LEDs will be blinking during firmware upgrade.
* Nyalakan Device UBNT
    - Wait for about 7 minutes (Warning: Do not disconnect the Ethernet cable during procedure).
* Lepaskan tombol Reset setelah ~10 detik (tidak lebih) sesudah device UBNT di nyalakan. Kita akan mengetahui-nya karena LED akan berubah.
* Ping 192.168.1.20. Jika ada responds, kita siap untuk meng-upload image. Jika tidak maka mulai lagi dari awal.
* tftp image menggunakan mode binary ke 192.168.1.20 sebagai 'flash_update'.
 
tftp 192.168.1.20
tftp> binary
tftp> trace
tftp> put  flash_update
 


Configuring IP addressl
Configuring IP addressl


Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account.
Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account.


==Prosedur Recovery Firmware==
==Prosedur Recovery Firmware==

Revision as of 02:42, 21 July 2012

Sumber: http://wiki.ubnt.com/Installing_OpenWRT_on_NanoStations/Bullets

Berikut adalah prosedur untuk mem-flash Ubiquiti Bullet 2 atau Nano2/Loco2. Prosedur ini akan mengganti AirOS firmware dengan OpenWRT firmware.

WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware”

Download OpenWRT

Download OpenWRT firmware untuk Ubiquiti dari 

http://downloads.openwrt.org/snapshots/trunk/atheros/
Nano2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-squashfs.bin
Pico2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin
Nano5 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt5-squashfs.bin

Flash Update

  • Set IP PC 192.168.1.x
  • Matikan Device UBNT
  • Tekan tombol Reset
  • Nyalakan Device UBNT
  • Lepaskan tombol Reset setelah ~10 detik (tidak lebih) sesudah device UBNT di nyalakan. Kita akan mengetahui-nya karena LED akan berubah.
  • Ping 192.168.1.20. Jika ada responds, kita siap untuk meng-upload image. Jika tidak maka mulai lagi dari awal.
  • tftp image menggunakan mode binary ke 192.168.1.20 sebagai 'flash_update'.
tftp 192.168.1.20
tftp> binary
tftp> trace
tftp> put  flash_update


Configuring IP addressl

Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account.

Prosedur Recovery Firmware

Referensi

Pranala Menarik

Retrieved from "https://lms.onnocenter.or.id/wiki/index.php?title=UBNT:_openwrt&oldid=33087"