OpenWRT: Mikrotik RB433

Mikrotik RB433 / RB433AH / RB433UAH Hardware

RB433 and RB433AH are rather similar boards, except for the microSD slot (RB433AH only), CPU frequency (300 vs. 680 MHz) and RAM size (64 vs. 128 MB). RB433UAH adds USB connector and 5V DCDC to power USB devices to RB433AH. RB433

RB433 Datasheet RB433AH

RB433AH Datasheet RB433UAH

RB433UAH Datasheet

UAH is the same board as AH, but with USB-connectors and dc/dc for 5V USB assembled. Adding unpowered USB to other boards could be easy, just solder in connector or simply wires. MicroSD Slot

The MicroSD Slot needs SPI-Bus sharing support, which is not implemented in Backfire.

SPI-Bus sharing has been implemented in Trunk r22862 the MicroSD Slot is usable now. Read speed ist about 0.92 MB/s (11/13/10: I get I/O and -89 errors on the SPI bus while assessing the microSD card) Netboot

The bootloader of RB433 is able to load an image in elf format via BOOTP into RAM and execute it. Build the Target

You need to get OpenWrt trunk. In menuconfig choose:

   Target System: Atheros AR71xx/AR7240/AR913x/AR934x
   Subtarget: Devices with NAND flash (mostly Mikrotik)
   Target Images: ramdisk

Now build the ram disk version. While it's building create the tftp-root directory if not already done and a symlink to the ram disk image

sudo mkdir -p /tftpboot sudo ln -sf $(HOME)/openwrt/rb433uah-netboot/bin/ar71xx/openwrt-ar71xx-nand-vmlinux-initramfs.elf /tftpboot/openwrt.elf

Setup the Host

You need a BOOTP and a TFTP server on your host machine, we use dnsmasq here, since it can provide both services. Install dnsmasq with:

sudo apt-get install dnsmasq

Changes in /etc/dnsmasq.conf:

   only listen on the interface which is directly connected to the RouterBoards WAN (PoE) port. e.g.

   interface=eth0

   allow a DHCP range, e.g.

   dhcp-range=192.168.6.100,192.168.6.119,12

   allocate an IP address to the board, e.g.

   dhcp-host=00:0C:42:XX:XX:XX,192.168.6.101

   (replace the XX with the MAC address of your board!)

   enable dnsmasq's built-in TFTP server

   enable-tftp

   set the root directory for files available via FTP.

   tftp-root=/tftpboot

   set filename (produced above) and tftpd server for BOOTP, e. g.

   dhcp-boot=/tftpboot/openwrt.elf,boothost,192.168.6.1

Finally restart dnsmasq

sudo /etc/init.d/dnsmasq restart

Setup the Target

   Connect to the serial port with a null modem cable (115200, 8N1).
   Press a key shortly after powering the board.
   Press o to change the boot device
   Press e to boot from ethernet in the future.
   Press x to leave setup (-o-e-x is needed only once, the boot method is saved in non-volatile memory)

If everything is setup correctly it should look like:

RouterBOOT booter 2.16

RouterBoard 433AH

CPU frequency: 680 MHz

 Memory size: 128 MB

Press any key within 2 seconds to enter setup.. trying bootp protocol.......... OK Got IP address: 192.168.6.101 resolved mac address 4E:80:00:00:00:00 Gateway: 192.168.6.1 transfer started ................................... transfer ok, time=7.16s setting up elf image... OK jumping to kernel code Linux version 2.6.26.7 (joerga@thinkpad) (gcc version 4.1.2) #2 Mon Nov 10 11:23:37 CET 2008 console [early0] enabled ...

Permanent Installation

You need a working netboot first, see above. Erase the NAND Flash

If you want to install OpenWrt permanently into the NAND flash you once need to erase the NAND flash to get rid of the RouterOS stuff:

   connect via serial line
   press a key shortly after powering the RB433 up
   press e and type yes to format the flash from the bootloader

Setup the Host

An HTTP web server is required on the host, e.g. mini-httpd in Ubuntu. Install the mini-httpd web server

sudo apt-get install mini-httpd

In /etc/default/mini-httpd change

   Start daemon

   START=1

In /etc/mini-httpd.conf change

   On which host mini_httpd should bind

   host=192.168.6.1

   Run in chroot mode

   chroot

   Where are the web files stored

   data_dir=/home/openwrt/rb433uah/bin/ar71xx/

Restart the mini-httpd web server

sudo /etc/init.d/mini-httpd restart

Build the Target

You need to get OpenWrt trunk. In menuconfig choose:

   Target System: Atheros AR71xx/AR7240/AR913x/AR934x
   Subtarget: Devices with NAND flash (mostly Mikrotik)
   Target Images:
       [*] tar.gz
       [ ] jffs2
       [*] squashfs

Build it. Install OpenWrt into Flash

   Start netboot (see above).
   Press ENTER to get a shell prompt.
   Execute:

wget2nand http://192.168.6.1

This script will set an IP address via dhcp on br-lan. The output should look like:

root@OpenWrt:/# wget2nand http://192.168.6.1 killall: udhcpc: no process killed udhcpc (v1.11.3) started Sending discover... Sending select for 192.168.6.101... Lease of 192.168.6.101 obtained, lease time 3600 adding router 192.168.6.1 deleting old routes adding dns 192.168.6.1 Erasing filesystem... Mounting /dev/mtdblock2 as new root and /dev/mtdblock1 as kernel partition yaffs: dev is 32505858 name is "mtdblock2" yaffs: passed flags "" yaffs: Attempting MTD mount on 31.2, "mtdblock2" yaffs: auto selecting yaffs1 yaffs: dev is 32505857 name is "mtdblock1" yaffs: passed flags "" yaffs: Attempting MTD mount on 31.1, "mtdblock1" yaffs: auto selecting yaffs1 Erasing existing files... rm: cannot remove '/tmp/wget2nand-rootfs/lost+found': Directory not empty Copying filesystem... Connecting to 192.168.6.1 (192.168.6.1:80) - 0% | | 0 --:--:-- ETA/ ./jffs/ ./tmp/ ./www/ ... Image written, you can now reboot. Remember to change the boot source to Boot from Nand

   Power-cycle the RB433 and change the boot source to NAND.

Switch setup Ethernet Jacks

The ethernet jacks are mapped to port numbers of the IP175C switch (looking at the front of the board):

[ port 4 (PoE)] ( serial ) [port 1] [port 2]

Switch Ports (for VLANs) Interface Switch port eth0 4 eth1 1 & 2

Port 1 and port 2 are switched in the default config. Useful Links

   Netboot for RB1xx
   phorn's patches for IP175C support with kmod-switch and swconfig
   a thread about RB433, IP175C and kmod-switch

Referensi

• http://wiki.openwrt.org/toh/mikrotik/rb433