OpenWRT: Flash Buffalo WZRHP300N: Difference between revisions

From OnnoCenterWiki
Jump to navigationJump to search
Onnowpurbo (talk | contribs)
69,477 edits
Onnowpurbo (talk | contribs)
69,477 edits
New page: Sumber: http://wiki.openwrt.org/toh/buffalo/whr-hp-g300n Set your ethernet interface ip on 192.168.11.2 Set your ethernet interface netmask on 255.255.255.0 Add arp entry for 192.168...
 
Onnowpurbo (talk | contribs)
69,477 edits
No edit summary
 
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
Sumber: http://wiki.openwrt.org/toh/buffalo/whr-hp-g300n
Sumber: http://wiki.openwrt.org/toh/buffalo/whr-hp-g300n


Install


sudo su
apt-get install curl


Set your ethernet interface ip on 192.168.11.2
Buat Script


Set your ethernet interface netmask on 255.255.255.0
vi buatflashbuffalo.sh


Add arp entry for 192.168.11.1 when the ethernet interface is up
Isi dengan


sudo arp -s 192.168.11.1 aa:bb:cc:dd:ee:ff
ifconfig eth0 192.168.11.2
arp -s 192.168.11.1 02:aa:bb:cc:dd:1a
curl -T openwrt-19.07.0-ar71xx-generic-wzr-hp-g300nh-squashfs-tftp.bin tftp://192.168.11.1 &


Download the tftp version of the right firmware Change the directory of your prompt to the firmware download directory cd /Users/yourname/Downloads/
Buat Script


Send your firware image with tftp
vi setip.sh


tftp 192.168.11.1
Isi dengan


*from this point, you're under tftp command prompt, the "tftp>" is the prompt tftp gives you, you just need to type the command AFTER that.
#!/bin/bash
while [ true ];
do
ifconfig eth0 192.168.11.2
arp -s 192.168.11.1 02:aa:bb:cc:dd:1a
done


tftp> verbose


tftp> binary
Save script di tempat firmware openwrt tersebut berada.


tftp> trace
chmod 777 pada script


tftp> rexmt 1
chmod 777 *sh


tftp> timeout 60


Power on your router on and plug your ethernet on a LAN port
Save script di tempat firmware openwrt tersebut berada.


Send the command put until is success
* Matikan Buffalo
* Masukan kabel LAN PC ke LAN4 Buffalo yang pas sebelah Internet.
* Masuk ke folder tempat image openwrt berada.
* Jadi superuser


tftp> put linux.bin
  sudo su


putting linux.bin to 192.168.11.1:linux.bin [octet] sent WRQ <file=linux.bin, mode=octet> tftp: sendto: Can't assign requested address
* Jalankan


tftp> put linux.bin
./setip.sh &
./buatflashbuffalo.sh


* Masukan power Buffalo


Akan tampak pada layar
  % Total    % Received % Xferd  Average Speed  Time    Time    Time  Current
                                  Dload  Upload  Total  Spent    Left  Speed
100 6656k    0    0  100 6656k      0  336k  0:00:19  0:00:19 --:--:--  483k
100 6656k    0    0  100 6656k      0  336k  0:00:19  0:00:19 --:--:--  336k
Jika kita cek arp -n akan tampak
arp -n
Address                  HWtype  HWaddress          Flags Mask            Iface
192.168.11.1            ether  02:aa:bb:cc:dd:1a  CM                    eth0




Line 46: Line 73:


* http://wiki.openwrt.org/toh/buffalo/whr-hp-g300n
* http://wiki.openwrt.org/toh/buffalo/whr-hp-g300n
==Pranala Menarik==
* [[OpenWRT]]
* [[OpenWRT: Download Firmware yang sudah jadi]]
* [[OpenWRT: Source Repository Download]]
* [[OpenWRT: Melihat Daftar Package]]
===Build Firmware===
* [[OpenWRT: Build Firmware]]
* [[OpenWRT: Build Firmware Download Source Pendukung]]
* [[OpenWRT: Build Firmware Buffalo WZRHPG450H]]
* [[OpenWRT: Build Firmware Buffalo WZRHPG300N]]
* [[OpenWRT: Build Firmware Buffalo WZRHPG300NH2]]
* [[Buffalo]]
* [[Buffalo: WZRHPG450H Cara Recovery]]
* [[Buffalo: WZRHPG450H OpenWRT mengaktifkan setelah di flash]]
* '''[[Buffalo: WZRHPG450H Membuat Firmware OpenWRT Sendiri]]''' '''COOL'''
* [[Buffalo: WZRHPG450H OpenWRT instalasi aplikasi Pendukung OLSRD]]
* [[OpenWRT: Build Firmware Ubiquiti NanoStation2]]
* [[OpenWRT: Build Firmware Mikrotik RB433]]
* [[OpenWRT: Build Firmware Linksys WRT160NL]]
* [[OpenWRT: Build Firmware Linksys WRT54GL]]
===IPv6===
* [[OpenWRT: IPv6]]
* [[OpenWRT IPv6: Build Firmware Linksys WRT160NL]]
* [[OpenWRT IPv6: Build Firmware Linksys WRT160NL Tanpa WebGUI]]
* [[OpenWRT IPv6: Build Firmware Buffalo WZRHPG450H]]
* [[OpenWRT IPv6: Build Firmware Buffalo WZRHPG300NH2]]
* [[OpenWRT IPv6: Setup tunnel ke tunnelbroker]]
* [[OpenWRT IPv6: Konfigurasi]]
* [[OpenWRT IPv6: Konfigurasi WAN6 dengan radvd]]
===Flash Firmware===
* [[OpenWRT: Flash Linksys WRT54GL]]
* [[OpenWRT: Flash Linksys WRT160NL]]
* [[OpenWRT: Flash Buffalo WZRHP450H]]
* [[OpenWRT: Flash Buffalo WZRHP300N]]
* [[OpenWRT: Flash UBNT NanoStation2]]
* [[OpenWRT: Flash UBNT NanoStation M2]]
* [[OpenWRT: Flash UBNT NanoStation Loco M2]]
===Misc===
* [[OpenWRT: Setup WiFi]]
* [[OpenWRT: Setup PPTP VPN Server]]
* [[OpenWRT: Setup OLSR di UBNT via CLI]]
* [[OpenWRT: Mikrotik RB433]]
* [[OpenWRT: Setup OLSR Sederhana]]
* [[OLSR - di OpenWRT]]
* [[OpenWRT: 3G modem]]
* [[OpenWRT: Build Firmware dengan 3G Modem Support]]
* [[OpenWRT: Setup Firewall]]
* [[OpenWRT: Konfigurasi UBNT NanoStation2 tanpa WebGUI]]
===UBNT===
* [[UBNT]]
* [[UBNT: Teknik Recovery]]
* [[UBNT: Upload Firmware]]
* [[UBNT: Rebuild Firmware]]
* [[UBNT: firmware dengan OLSR]]
* [[UBNT: openwrt]]
* [[UBNT: olsr dengan openwrt]]
* [[UBNT: olsr dengan kamikaze openwrt]]
* [[UBNT: olsr dengan backfire openwrt]] '''RECOMMENDED'''
* [[UBNT: UniFi]]
* [[UBNT: UniFi Konfigurasi Awal]]
* [[UBNT: UniFi Manajemen HotSpot]]
* [[UBNT: OLSR Pembuatan Firmware]]
* [[UBNT: OLSR Konfigurasi]]
* [[OLSR - di UBNT]]
* [[OLSR - di Ubuntu]]
* [[OpenWRT]]

Latest revision as of 05:38, 14 January 2020

Sumber: http://wiki.openwrt.org/toh/buffalo/whr-hp-g300n

Install 

sudo su
apt-get install curl

Buat Script 

vi buatflashbuffalo.sh

Isi dengan 

ifconfig eth0 192.168.11.2
arp -s 192.168.11.1 02:aa:bb:cc:dd:1a
curl -T openwrt-19.07.0-ar71xx-generic-wzr-hp-g300nh-squashfs-tftp.bin tftp://192.168.11.1 &

Buat Script 

vi setip.sh

Isi dengan 

#!/bin/bash

while [ true ];
do
ifconfig eth0 192.168.11.2
arp -s 192.168.11.1 02:aa:bb:cc:dd:1a
done


Save script di tempat firmware openwrt tersebut berada.

chmod 777 pada script 

chmod 777 *sh


Save script di tempat firmware openwrt tersebut berada.

  • Matikan Buffalo
  • Masukan kabel LAN PC ke LAN4 Buffalo yang pas sebelah Internet.
  • Masuk ke folder tempat image openwrt berada.
  • Jadi superuser
 sudo su
  • Jalankan
./setip.sh &
./buatflashbuffalo.sh
  • Masukan power Buffalo

Akan tampak pada layar 

  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
100 6656k    0     0  100 6656k      0   336k  0:00:19  0:00:19 --:--:--  483k
100 6656k    0     0  100 6656k      0   336k  0:00:19  0:00:19 --:--:--  336k

Jika kita cek arp -n akan tampak 

arp -n

Address                  HWtype  HWaddress           Flags Mask            Iface
192.168.11.1             ether   02:aa:bb:cc:dd:1a   CM                    eth0


Referensi

Pranala Menarik

Build Firmware

IPv6

Flash Firmware

Misc

UBNT

Retrieved from "https://lms.onnocenter.or.id/wiki/index.php?title=OpenWRT:_Flash_Buffalo_WZRHP300N&oldid=58548"